Wishlist(0)
tiktokgroups.com
Categories See All >

American Nigels 3D Printing LLC 2 Pack USA MADE Milwaukee M18 Battery Adapter 18v Connector Dock Holder Mount Injection Molded

(751 Reviews)
Price
$23.99
Quantity
(10000 available )
Total Price
Share
14 Ratings
13
1
0
0
0
Reviews

  • Phillip

    > 24 hour

    Definitely not 3D printed crap

  • D Lukes

    > 24 hour

    I have installed these on dewalt xrp tools, old milwaukee tools, car radio, and fish finder. Ill likey buy more, and find more uses.

  • MB_designs

    > 24 hour

    So far working great! I have used them on a variety of projects from making a 36 volt kids electric bike to run on two Milwaukee batteries to powering a 12v air compressor with a m18 battery.

  • Kevin F.

    > 24 hour

    Solid construction, good fit to M18 battery, spade electrical connectors seem molded into place and do not move, also solid. Make your own wires to attach and you have instant power from your Milwaukee 18 volt batteries. Exactly what I was looking for.

  • Jennifer Ward

    > 24 hour

    I use these adapters from powering my kids power wheels to starting my Honda Grom scooter.

  • Jared

    > 24 hour

    I use these on e bikes, I’ve tried them all but these actually don’t break and hold tight

  • Thomas L.

    > 24 hour

    This is well built, many holes to secure it to frame. 5 stars

  • Rob Christie

    > 24 hour

    High quality

  • dmentd1

    > 24 hour

    Great product to breathe new life into old tools. Much better fit on batteries than other adapters on the market

  • John Tabor

    > 24 hour

    Wired two of em in parallel to give a hella long runtime to a kids John Deere gator, they love it. VERY worth the money, these are much sturdier than others Ive seen.

Adapters Proudly Made in the USA. Adapters are made of glass reinforced nylon 6 (PA6-GF30) which is the same material the drills are made out of. Adapters have 6 countersunk bolt/screw holes for mounting on walls, vehicles, etc , bolts/screws not included. Adapter has 2 6.3 mm brass male spade connectors over molded into the adapter that you plug your wires into. Terminals are 20 gauge yellow brass which is 70 percent copper 30 percent zinc for high power applications. Adapters have pluses and minuses on both sides of them indicating the positive and negative terminals. Adapter is based on my best selling 3d printed model but this is 5x stronger, and can be used outdoors. DISCLAIMER THESE UNITS DON"T HAVE ANY PROTECTION CIRCUITS IN THEM, USE AT YOUR OWN RISK. The following bullet points are directions on how to use this injection molded Milwaukee M18 battery Adapter. The first step is to mount the adapter where you want it, the holes are for M4, #8, or other flat head screws. Run your preferred wire (silicone, pvc, pe, nylon etc .) and preferred gauge (10, 12, 14, 16 etc .) to the adapter. Solder wires onto brass terminals or crimp female 6.3 mm spades onto your wires, and plug them into the adapter. You can run your wires horizontally or vertically out of the adapter, vertically stays inside the adapter for a low profile. Additional helpful Information You can connect most batteries in parallel and/or series if the batteries are exactly the same. If you don"t want to over discharge your battery use a digital low voltage protector disconnect If you want a higher voltage like 24, 36, 48, or 60 volts use a dc to dc step up boost converter If you want a lower voltage like 5 or 12 volts use a dc to dc buck converter

Related products

Shop
( 1745 Reviews )
Top Selling Products
Home
Categories
Cart (0)
Messages
Account
0 Cart Item (s)

Your Cart is empty