ANYCUBIC FEP for Photon Mono X/Photon X/Photon Mono X 6K/Photon M3 Plus, 2 Pieces

Not much to say other than it does what its intended to do.

The item shipped quick. Its the exact same high quality as the original.

For those “crying” about not having enough instructions? Figure it out! It gives basic instructions on what to do on the back of the package . Does not take a brain surgeon to do this. Hope are not pre-cut! You have to do them yourself after you line everything up correctly. A simple trick after you have removed the old film, lay it on a desk and place to two clamps together. Line up the film as even as possible and I hope you are using a good multi-hex key tool. Slide the assembly slightly over the edge of the desk and use the hex key to pierce your first hole in the center. Insert the screw and tighten(but not all the way). Then move around and follow this order. Bottom top left right and back to bottom. Find a screw hole that is opposite when going around until it’s good and even then tighten it well. I have an example of the pattern I followed but this is for the main screws. Follow similar for the 22 small screws.

I have not had to use them yet these are my spares I know Im going to have to use them cuz these are perishable Parts on your resin 3D printer but I got them by my side

I bought this a while back and installed it on my resin vat. It shipped with a thick plastic sheet to keep the fep films from creasing during shipping! The films come with protection sheets on both sides of them as well!! Anycubic has a wonderful example video on YouTube on how to install it. I greatly recommend watching it so that you can properly adjust the tension! Overall, I love the sheets, love the shipping, and love the printer it goes on!!!!

It’s really a great product! It’s really important to remove the old FEP and when installing the new one not to damage it. First disassemble the old FEP and then wipe everything down. Open the new packaging takeoff the protective color on both sides of the FEP screen. At that point what I do is secure for corners when installing the FEP between the two brackets that hold it in place. From that point a puncture holes in every single screw hole to make it easy to put the screws in. Once the screws are all secure with a razor blade I cut off the excess FEP material. This is great that they make the FEP larger so that way you get it inside correctly and that you won’t have any leaks in the future with your resins. From that point I puncture all the Large screws through the FEP And then lower the entire FEP into the VAT frame. From that point I slowly start screwing in the screws evenly with the provided Allen wrench that came with the unit. Tighten the screws slowly until you’re not able to tighten them at all. Again I work in a circular motion around the VAT so that I am tightening everything evenly. Once you’re done tightening the screws you will need to clean both sides with glass cleaner which will give you an amazing result using a microfiber cloth. I personally add FTPE lubricant from 3-in-one Inside the VAT and wipe it down with the micro fiber cloth. This step ensures that I do not have any failed prints. I do this before I add resin to the VAT. The Anycubic Mono X is a Great Product. Chafing the VAT Sceen is super easy! Take your time and don’t damage the FEP or you will have crappy prints! They also give a screen protector free, I have to figure out how to use that.

This ANYCUBIC FEP film for the Photon Mono X 6K is a solid 5-star product. Its easy to install and offers impressive performance on my 3D printer. I have found that prints adhere well, yet they are easy to remove, reducing potential damage to my models. Furthermore, the film is remarkably durable, showing little signs of wear even after multiple uses. The two-piece pack provides great value, as I have a spare ready for when I need it. The transparency of the FEP film also ensures that I can keep an eye on my prints as they progress. This product is a definite win for anyone using the Anycubic Mono X 6K.

What the heck is this? It was supposed to be for the Anycubic Mono X it is too big, not cut correctly and has no holes for the screws. Looks like they split an 8x10 piece of FEP in half with the world’s dullest scissors and charged me 40 bucks for it.

Had to find better instructions for installation on YouTube but once I installed it correctly, with the correct tension, it worked just like new. Only wish they included better instructions and more than 2 sheets.