BIGTREETECH DIRECT TMC2209 V1.2/V1.3 Stepper Motor Driver Silent UART Stepsticks VS TMC2100 TMC2130 for SKR 2/ SKR V1.4 Turbo Manta M4P Manta M5P/M8P 3D Printer Motherboard (Pack of 4pcs)

Worked perfectly for my Tenlog Printer. I had a fan fail and the heat smoked the 2209 chip for Extruder E1. Ordered the 4 pack and attached 2 of the packaged heatsinks for extra cooling and I was off to the races in under 20 minutes.

This stepper driver was to replace one on a functioning 3D printer. The existing one was a 8825 for the bed axis. I was getting overshoot at high speeds, and thought a larger motor with a driver that could handle more current would help. So far, I replaced the driver, but not the motor yet. I had to change a jumper setting on the board, so the steps would match my existing setup, as the 8825 used the jumpers in a different config. It works well, and made that axis of the printer much quieter. However, it actually doesnt hold as well as the 8825 did. I tried adjusting the current, but would still lose steps at high speeds, where the 8825 could still hold. I had to adjust my jerk speed down some for this driver, and it is smooth and quiet, but was hoping for more on the holding power. Maybe with a new motor, it will do better. If youre looking for a cheap upgrade to really cut down the noise, then this is for you. I wasnt concerned about noise, just looking for something that could handle more current.

Used these on my TronXY X5S with the Big Tree Tech SKR 1.4 board. These drivers are great. Im using them without end stop switches and that works wonderfully. These drivers and that control board made the X5S so much quieter and smoother. It was the best upgrade Ive done for that printer. Id greatly recommend these.

swapped my a4988 drivers out for two of these and plugged them in and put a jumper between the en/gnd on my cnc shield and they worked right away! the vref came set perfect for my 1.5a steppers and they make ZERO sound!

They definitely made my anycubic mega s quieter but one out of the 5 came not working. So I had to use one of the old drivers so my printer isnt as quiet as it could be. I paid for 5 but only got 4 working. The 4 that work are good though. Def makes the printer quieter.

Silent, with sensorless homing. Easy to install, clear instructions

Hi Quality parts, definately worth the money... and the kids love the little rubber ducks.

So I have to say right out of the gate that Biqu was great about replacing the motherboard on my printer when it failed. The failure also caused the print head/hotend to gum up real bad and it was pretty well ruined, and they replaced that as well. When swapping out the stepper motor drivers I likely ruined one unless it got damaged when the motherboard failed. Either way, I ordered these on my own to replace the ones that came with the original motherboard. THEY WORK GREAT! They literally are plug and play and my stepper motors are super silent. If you want to upgrade or just replace failed stepper motor drivers, these are an excellent choice.

Worked great! Silent drivers and stall guard make these stepper drivers the best I’ve used. Worked well with SKR1.4Turbo board. Bought two sets for a future build as well. Highly highly recommend. Box Even included a small pin layout for the driver.

Ender 3 Pro + SKR v1.4Turbo + TCM2209 Stepper drivers = 1 Awesome Printer! compared to the basic Ender 3 Pro steppers, these are 1 hell of an upgrade! You go from EeeEEEeEEeeeE sounding movements to Wooooosh Wooooooosh hahahhahahha Read the instructions carefully, you may need to cut a pin off the driver board. Easy tho. The included heat syncs really do a great job as well. Ive run a couple prints, lasting a few hours, without having the lid on my components case, so no fan... Never had the printer shutoff from overheating. As long as you update you firmware correction and using a compatible board, these stepper drivers are great!