FivePears Up&Down Cut Compression Spiral Router Bit for CNC, 1/8 inch Cutting Diameter and 3/4 inch Cutting Length 1/4 in Shank Carbide End Mill Router Bit for Wood Carving Engraving Grinding Grooving
-
Mario Alvarez
> 24 hourPersonally, I believe they are way better than the ones that cost twice the price!!!
-
Winston Churchill
> 24 hourSharp, introduced me to spiral cut bits, must have
-
Joey Thunder
> 24 hourThis is well made, every bit as good as the more expensive Freud and Rockler bits I own. It comes in its own plastic case that closely matches the size of the bit for easy storage. It may seem trivial, but I store my bits in their original packaging, and the cases on Freud bits huge, so much bigger than the bit they hold, this case is perfect for how I like to store my bits. I haven’t used it enough to speak on its long term durability yet, but there are no red flags yet as far as the cut quality or craftsmanship is concerned. Recommended.
-
Mario Alvarez
> 24 hourPersonally, I believe they are way better than the ones that cost twice the price!!!
-
Chris C Gaston
> 24 hourI liked how clean it cuts. I ise this on a cnc for cutting out letters and pockets in wood.
-
Kurt In Iowa
> 24 hourI wanted to make slotted holes in oak. These pieces were an inch thick and for holding a table top on. The bit cut clean, fast and held up for multiple holes. Ill be buying more from this company.
-
James Mccormick
> 24 hourI picked up this item not knowing much about it. I found out REAL quick it was not very durable. Within the first 5 minutes of using it it broke. I returned it to amazon and got a replacement. Well it wasn’t a fluke. The replacement did the same thing. Will not be buying another.
-
B.
> 24 hourused for my cnc router. good product
-
Kyle Emerick
> 24 hourNormally after 10-20 sheets of parts, most bits have chipped tips. This bit has gone 92 sheets so far and still looks great. This after cutting about 20 parts per sheet in 3/4 ACX.
-
David Silva
> 24 hourNice as most better I dont know price was right Shipping was on time its my back up used it twice like it in plywood down cut
|
|
|
|
|---|---|---|
UP Cut BitUp-cut bit leaves a smooth bottom edge but a rough top edge. The up cut is better at evacuating chips, Ideal for mortise and tenons, grooving, slotting or routing deep blind holes. It performs faster cutting while pulling the chips up. |
Down Cut BitDown-cut bit leaves a clean top edge but a rough bottom edge. It is great for cutting shallow dados, rabbets, and visible slots. When cutting dados or grooves with a down cut bit, be sure to slow the feed rate to allow more time for chip removal. |
Compression BitCompression bit cut both top and bottom cleanly, Its spiral action pulls both sides into the center of the bit where it ejects out of the side. Through cuts in harwoods, softwoods, plywood, melamine, and other veneers |
|
|
|
|
|
|
|---|---|---|---|---|---|
| UD28408(Compression Cut) | UC28410(Up Cut) | DC28410(Down Cut) | UC28405(Up Cut) | DC28405(Down Cut) | |
| Cutting Diameter | 1/8 inch | 1/8 inch | 1/8 inch | 1/8 inch | 1/8 inch |
| Cutting Length | 3/4 inch | 1 inch | 1 inch | 1/2 inch | 1/2 inch |
| Shank | 1/4 inch | 1/4 inch | 1/4 inch | 1/4 inch | 1/4 inch |
| Material | UF09 Solid Carbide | UF09 Solid Carbide | UF09 Solid Carbide | UF09 Solid Carbide | UF09 Solid Carbide |
| Recommended Rotational speed(Wood) | 18000 | 18000 | 18000 | 18000 | 18000 |
| Feed Rate(MDF Laminate) | 140(inch/min) | 160(inch/min) | 130(inch/min) | 160(inch/min) | 130(inch/min) |
| Feed Rate(Soft Wood) | 125(inch/min) | 140(inch/min) | 115(inch/min) | 140(inch/min) | 115(inch/min) |
| Feed Rate(Hardwood) | 110(inch/min) | 125(inch/min) | 100(inch/min) | 125(inch/min) | 100(inch/min) |