Koroao Metal Wall Mount Holder for Orbi Whole Home Tri-Band Mesh WiFi 6 System/Orbi Ultra(RBK850)(RBK852)(RBK853)/(RBS750)(RBS751)(RBK752)(RBK753)(960/860 Series)/(AX4200)(AX5700)(AX6000) (2-Pack)

Great product

Very sturdy. They work very well.

Very solid

I have tried almost all the top end router solutions out there and if you want full coverage with AX WiFi-6 tech, this is the only one that delivers a clean setup. If you want top notch networking features and also the best performer when it comes to great coverage and performance then go with the Nighthawk RAX120. I tried the RAX200 and while it might have more bands the coverage sucks compared to the RAX120. If i did not need the extra coverage that the Orbi AX6000 provides; I would have stock with the RAX120, since its also an AX6000 router.

Works as advertised

Easy install

Very simple item and does what it is designed to do. The only negative is that it should of atleast came with instructions on the right drill bit. I know that this item is percieved as (duh) you dont need instructions for screws and wall anchors.. But I wish I had it...

Installed in minutes. Love the minimalist design, no unnecessary parts or design. My only complaint is that the fit for the wires to the Orbi router can be a bit tight to get through if youre short on length of cable, so plan to place them accordingly.

Whats to be said about these mounting brackets? They are strong, good-looking and a perfect fit. High quality and a good value for something that (at the price) should have come with the Orbi mesh system to begin with. Highly recommended.

I bought this to mount an Orbi satellite in my workshop to go along with a new NETGEAR - Orbi AX3000 Tri-Band WiFi 6 Mesh System (3-Pack). I had already installed the RBR750 router at the modem, and the 2 included RBS350 satellites placed within my home, and had already ordered an additional NETGEAR - Orbi AX4200 Tri-Band Mesh Wi-Fi 6 Satellite to install in my workshop. However, when I inspected the bottoms of the RBS350 satellites, I noted that they are NOT constructed with the embedded nuts in the base. The router, on the other hand, does have the nuts. And the images of the Orbi AX4200 satellite on the stores website did not show the base of the satellite. I spent a lot of time making a plexiglass support stand to adapt to the wall mount for the satellite to be able to install in the workshop (before receiving the additional satellite). Had everything made to fit the wall mount before the new satellite was delivered. Upon receipt and opening the package, I did see that the new Orbi AX4200 Tri-Band Mesh Wi-Fi 6 Satellite had the nuts in the base! Everything did install easily. The satellite is quite steady attached to the mount. Unfortunately, Id wasted a couple of hours making a holder that I didnt need (which is a good thing). Summarizing, if you are purchasing the Metal Wall Mount Holder for Orbi Whole Home Tri-Band Mesh WiFi 6 System/Orbi Ultra(RBK850)(RBK852)(RBK853)/(RBS750)(RBS751)(RBK752)(RBK753)/(AX4200)(AX5700)(AX6000)(1-Pack), you might want to check that your satellite does have the embedded nuts in the base BEFORE ordering this item. Please note that it does fit the RBR750 router, and it does fit the Orbi AX4200 Tri-Band Mesh Wi-Fi 6 Satellite, but DOES NOT fit the RBS350 satellites, unless you are prepared to make a bracket that fits on the mount to allow the satellite to sit in. If needing to do this, one can pick up a small sheet of thin plexiglass and cut out a piece that fits the base of the satellite, and taking into account making the sides, you can cut out small pieces on 2 corners (in the front), and using a metal straight edge, one can heat the area where you want to bend the plexiglass with a heat gun set to around 700 degrees F (dont heat too much to cause the plexiglass to bubble), and bend the edge up to a 90 degree angle - do this for the front and 2 sides. Overall, a great product, fits the satellite well (the one with the embedded nuts). Highly recommend!