Lift Supports Depot Qty (2) Fits Camry 2007 To 2011 Front Hood 10030744 200186 24761 5344006050 53440-06050 5344006050B 5344006051 53440-06051 5344006052 53440-06052 5344006060

(1834 Reviews)

Price
$29.95

Quantity
(10000 available )

Total Price
Share
63 Ratings
59
4
0
0
0
Reviews
  • Carrie Peterson

    > 3 day

    Perfect fit & function for my toyota camry hood lifts. Like new again. nice quality.

  • Mr Impulse Purchase

    > 3 day

    Quick install. I would recommend propping a paintcan or some other wedge under the hood to keep it fully open during installation. Took more time getting the old ones off than the new ones on.

  • Judith Lodes

    Greater than one week

    These fit perfectly.

  • Sean L.

    > 3 day

    This was a perfect fit replacement for my wifes 2007 Camry LE hood support struts. Took seconds to replace both with a small flathead screwdriver. I always recommend replacing both, even if you have one bad. Usually if one is about to go, the other isnt far behind it. For the price, just replace both and dont worry about it for a long time. It does appear these are near factory-replica, I couldnt visually see much of a difference between the OEM ones and these. Now my wifes hood lifts up again and holds itself up without the need of vice grips. Makes my life easier doing oil changes, tune-ups, water pumps, batteries, etc.

  • Da ha y n

    Greater than one week

    Headline says it all

  • Manuel Lizarraga

    Greater than one week

    These type of struts are normally 2 to 3 times what these costed. So easy to install, just need a small flat screwdriver or a similar tool. very impressed with the quality and value.

  • Earl

    Greater than one week

    No hassle replacement if there are any problems.

  • odonabit

    > 3 day

    popped em straight on...no problema... perfect fit

  • Kat

    > 3 day

    Not too expensive and it does the job. Awesome!

  • terrance callender

    > 3 day

    Would purchase again...... Fits perfectly!!!

Why Purchase from Lift Supports Depot?

Lift Supports Depot PictureLift Supports Depot Picture

QC StationQC Station

RemoveBallStudZoomRemoveBallStudZoom

Premium Quality Supports

Lift Supports Depot supports undergo a vigorous QC process to help ensure dependability. Lift supports internal components get assembled and mechanically tested to ensure internal parts are not installed incorrectly or missing. OE quality seals are incorporated to prevent low friction losses and oil seepage. Airline hydraulic oil helps to avoid crystallization and blockage during cold weather.

After painting and curing, lift supports are tested again for pressure and printed with final product information and lot numbers for traceability.

Vigorous Quality Control Process

The supports are pressure-filled and tested one by one for forces to be within accepted tolerances. Pressurized lift supports go through a pre-paint phosphate treating process, which helps the paint adhere properly to the body of the lift support and gives a long paint life.

Most importantly, an automated paint cabin is used for painting and curing in one place. Our lift supports never have premature rusting at the extremities due to the capillary effect of paint in bent areas.

Easy to Install

Most applications are quick and easy to install. Often times requiring nothing more then a flat headed tool to remove and replace. The hardest part is often finding someone to hold the Hatch or Hood while you swap them out.

Remove Ball socket from VehicleRemove Ball socket from Vehicle

Easy 4 Step Installation Process

Lift Supports Depot Supports are designed to be easy to install and maintain OEM design. Most install simply with the use of a Flat Head tool, and an assistant to hold the hatch or hood open. We do not recommend doing this alone, many hatches are very heavy and can result in injury if done without help.

Remove Ball socket from VehicleRemove Ball socket from Vehicle

Insert a Flat Headed tool behind the U-Band.

Pull back and remove ball Socket from StudPull back and remove ball Socket from Stud

Slightly Pull Back on the U-Band, allowing the claw to release the ball stud. Careful that you do not remove the U-band from the Support.

Press Ball Socket over Ball StudPress Ball Socket over Ball Stud

Place new support over the ball stud and press the ball socket over the ball stud.

Carefully Tug to Ensure SecureCarefully Tug to Ensure Secure

Once this has been completed for all mounting points, carefully tug to ensure all ball sockets are secure on ball Stud.

Related products

Shop
( 3635 Reviews )
Top Selling Products