(Waterproof Camera Junction Box) Universal Bullet Security Camera Mount Bracket Hide Cable, Metal Electric Enclosure, Outdoor Camera Cover, Base Junction Box for CCTV Cams (8 Pack)

I purchased these to provide a way to mount my cameras easily, have the ability to remove cameras easily and keep Ethernet cabling protected. The cover offers a large amount of threaded camera mounting hole configurations. The cover comes with a gasket and mounting screws. The construction is very nice and well built. It comes in white, which is what I wanted, but I imagine you can spray paint it to a color that matches the surrounding colors. I would highly recommend this for a clean and professional looking install. Install: For a solid mounting surface, I added 2x6 wood block above soffits and drilled a 1 hole through blocking. I attached the junction box to blocking. The soffit material was cut to fit around the junction box and I caulked around the junction box to weather seal. Bullet Cameras: Most bullet cameras I have seen, allow you to adjust pitch but not always horizontal angle when mounting to a soffit. Before installing, I suggest you figure out the mounting hole configuration for your cameras and temporarily mount camera to understand camera position relative to the junction box mounting position. This will allow you to figure out horizontal angle of the camera (4 positions depending how you attach cover.

Add a professional look tocthe installation.

Used this product many times. Never had as issue. Plan to purchase in future.

solid construction. my only problem is that they were too small for the cameras im using. i ended up returning these and decided to go in another direction using more cheaper, but solid, mounting box. cameras with a smaller than 4” base are ideal for these

Fit the cameras but put on 3/4” flex conduit the nut would not turn inside the box, the threads will push inside tight without the nut on some sealer good to go

I am an installer with my company that provides security services both for residential/commercial clients. I must say, hands-down over the years these are my go-to universal junction boxes. Ive tried plenty in amazon and also other suppliers, these by far are my most preferred. They are Metal and sturdy, do not rust and have a good amount of screw patterns for most cameras that i use (mainly lorex and Reolink - bullets). They also have very good weather-locking rubber seals that block the water out and are tight enough only for the cable to pass through (cat5e, cat6, coaxial etc). Lastly, as you can see from the picture they also work with piping, i specifically use these with 1/2 piping. I cant recommend these enough!

Installing these was easy. No sweat (except for the 98° weather). Good size, good quality. I did not use the provided installation screws and anchors. I installed into siding - therefore I needed longer screws

I installed cameras in my house. And for sure this is the right product for this!

Bought these to support my 8-camera Lorex System. Originally looked at the Lorex boxes and even the Amcrest boxes which were more than double the price. I decided to give these a shot and so far, theyve held up very well. Easy to install and enough room to house the ethernet cable and connector. Looks neat and professional, and didnt cost an arm and a leg. Use clear silicone at the joints and screws, and these should last a lifetime.

For three of my interior cameras, I modified regular electrical boxes from Home Depot, drilling holes in the face plate to fish in wires and mount the cameras, then painting them house colors instead of gray. But for the eight cameras that were going outside, I REALLY didnt want to do that much work. These fit the bill almost perfectly, and I wish Id gone looking for them sooner. Overall theyre sturdy in the hand, seemingly made of good materials. (I guess time will tell on that... being out in the Las Vegas sun will certainly put them to the test.) The center holes and their removeable plugs made wire placement easy, however I did have to cut my removeable center plugs so that they would wrap around my wires, rather than pulling the wires through the hole. But thats because I had a big honkin network connector that simply wouldnt fit through the plug hole. One puzzling thing was the camera mounting holes on the faceplates, which took a minute to wrap my head around. These appear to be designed to fit about eighty thousand styles of camera, with mounting holes all over the faceplate. At first I was annoyed thinking that the holes penetrated the faceplates and made them swiss cheese, but they didnt, theyre only partial holes. My particular cameras sat a little low-of-center on the faceplate, which gave me minor concerns of possible water seepage into the center hole. But after mounting everything and looking it over, Im confident water wont be an issue. (This has not been tested yet though.) The one negative I can give these is that theres only two punchouts for conduit to attach. This might not seem like a big deal, but depending on where your conduit is going to run, (left, right, top, bottom), it makes a difference because of the way the faceplate mounts to the body. Because the faceplates already have holes to mount the cameras, and because the faceplates only mount to the body in a certain orientation, that could be problematic to someone depending on how the body needs to be mounted to accept their conduit. In my case it wasnt an issue because I had conduit coming into the bottom, but for someone else I think it could be. All in all its a good product though, and I have no buyers remorse.