2023 New Upgrade WiFi Extender Booster Repeater, Up to 8000sq.ft and 45+ Devices, 2.4&5GHz Dual Band Wireless Internet Repeater and Signal Amplifier for Home & Outdoor, Supports Ethernet Port
-
MARGARET
> 24 hourI was able to install it in about 10 min and i now have wifi throughout the backyard.If you are looking for a easy to install wifi extender. this will work.
-
MARY
> 24 hourSuper easy set up, and now I can finally stream movies & music all over the house - no more dead spots!works great. I had to replaced my other extender after it died. this one works great.
-
PATRICIA
> 24 hourThis works great! It exceeds my expectations. Im in a room where I have trouble getting Wi-Fi and this device is able to capture it and I now have Wi-Fi all the time!
-
Marcel
> 24 hourMan bekommt hier ein wirklich preiswertes und absolut ausreichendes Netzwerkkabel.
-
JEREMY
> 24 hourDealt with crappy WiFi for a few years now, Finally got to a point of trying something. Put in one of these and wow now I got WiFi on the other end of the house reliably. Easy to install if you read the directions. Performance is good in my house.
-
tyskalio
> 24 hourUnschlagbares Preis-Leistungsverhältnis.
-
MARGARET
> 24 hourWorks great, Had very poor internet in the front of the house,Less than 5 minutes up and running, plug it in, turn on your l Pad or etc go to settings and follow instructions.
-
CHRISTINE
> 24 hourWe would not be able to watch streaming movies on master bedroom smart TV without this very helpful Wi-Fi range booster. It works as advertised. It came on time and had idiot proof installation guide.
-
CHRISTINE
> 24 hourSetup was not as intuitive as it should have been, but this is a great value and does the job. If you are comfortable with less than plug and play setup this is a bargain
-
JEREMY
> 24 hourWorks great! Installation was so easy. Just touch WPS on the router, then the button on this extender.. A few seconds later, we were able to use our wireless in a bedroom that had never had it before. Worth every penny! I like it!
|
|
|
|
|---|---|---|
4*3 dBi External Antennas180° and 90° rotating antennas can eliminate dead area and improve your existing WiFi coverage. For better performance and stable WiFi network with speeds of up to 867Mbps, 2.4GHz has farther penetration while 5GHz has faster speed. |
Smart Signal IndicatorsSignal LED indicates wireless signal strength between WiFi extender and your existing router. After initial setup, you can move your WiFi extender to any electrical outlets by reading the color of signal LED. |
With Vent Hole & WAN / LAN PortAir vents on both sides enhance heat dissipation capacity of the WiFi extender and ensure a safe working environment. Its WAN / LAN Port allows the WiFi extender to act as a wireless adapter to turn a wired device into a wireless one. |
|
|
|
|
|---|---|---|
Repeater Mode - Wireless to WirelessAmplify the WiFi signal of the wireless router, extend the coverage of the WiFi signal, and effectively solve the problem of weak WiFi signal and WiFi dead zone. (Suitable for home, office use) |
Repeater Mode - Wireless to WiredConvert wifi signals into wired signals through network cables to meet the network requirements of wired electronic devices, such as TVs, desktop computers, etc., reduce the distance of network cables, and avoid cluttered network wiring. |
Access Point Mode- Wired to WirelessUse Ethernet cable to connect this WiFi booster range extender to any Internet enabled Ethernet port in your room or Ethernet port of existing router, you can create a new dual band wireless network. Excellent for using at home or when travelling in hotel rooms. |
Reminder:
- The working status of the repeater can refer to its smart indicator light.
- WiFi signal booster is only limited to increase the coverage of the wireless signal, but not to increase the speed of the network.
- When the repeater expands the signal, it does not need to plug in the network cable. It can receive the signal of the router directly by plugging it into the socket, and transmit the wireless signal.
- When the repeater is unplugged or powered off after the setting is completed, it does not need to be reset. The original configuration information has been saved, unless you manually restore the factory state.