Comgrow 3D Printer Warm Enclosure Fireproof and Dustproof 3D Printer Tent, PVC Laminated Polyester Constant Temperature Protective Cover Room for Ender 3/Ender 3 Pro/Ender 3 V2/Ender 5 Pro

This did the job so well that I bought a second one for my recently purchased mini 4k resin printer and it fits great on it.

Only complaint would be, like another post here, it has no zipper flap on side for swapping out filament

Nice product. Fit the laser well. Air exhaust port worked as expected.

The things it does good are - keep the air temp around the print more consistent, slow the moisture uptake on exposed rolls on the printer, look nice, and keep smells in, and pet hair out. You should take care assembling. The black rubbery coating on the outside of the shell is not very durable. Putting it over the frame on an unswept floor was enough to put small holes in it, that allow the light of my printer to seep out. Not really a huge deal, but definitely not desirable.

I bought this tent because there was a discount for it when buying the Ender 3 Pro 3D printer. I wanted an enclosure to help reduce the risk of fire and also to help contain the heat of the printer for better prints. The tent set up was simple, aluminum tubes fit together with corner plastic fittings. My first issue I had was getting the cover on the frame. It just slips over and zips up but perhaps the manufacturer didnt allow for the extra space the corner fittings take. I tore one seam right on the corner trying to get it in. With the seam open slightly it now fits tight - but not too tight. I probably can fix it with some thread later. The size is good, it accommodates the printer and a 1K roll of filament. I also have a wireless camera in the enclosure for monitoring the printer and I likely have room for a small lamp too. There are velcro flaps on the back and side for cords. Things I would change: 1. Changing filament is a bit more of a challenge because I need to access the left side. I end up pulling the top front corner down and off the frame to access the filament feed. A zip open panel would be nice here like the front. 2. The clear plastic viewing window is not really clear. Its hard to see whats going on with the printer and I rely on the camera I have in there more than looking through the window. I would almost prefer a smaller peek through window and have the tent be more of the fire resistant material. Overall I like it. The tent does what it needs to and until I decide to build a custom enclosure it should work fine for my needs.

It was easy to put together, and it was a lot bigger than I expected! This has great access hole for all your cables (Power, USB, etc.) Plus, they have velcro vents on the bottom rear , left and right, so they are good to stay open or shut to keep bugs and unwanted things out, or can be used for needed ventilation. It has a rubbery outer skin, and feels like its nice and thick! It has a little pouch on the front lower right side to put things in, like a micrometer, or allen wrenches, and whatever, and has a nice big front opening that zips all the way up and back to give you plenty of space to work on it, and has a real nice, clear viewing area, so you have plenty of room for needed stuff like a camera, or other things inside the enclosure. Has about 12 front and back clearance when my Ender3 is centered in it! This would be perfect for virtually any printer! I saw my friends Ender 6, and it would fit in this thing. I absolutely love it, and might even get some more of these for other stuff! You could use this as a grow box for herbs, and whatnot, or if you think outside the box, you could even use this for a bird cage cover for a well ventilated area that you could safely close the front for noise reduction, and plenty of fresh air travelling through the area, and for quiet time at night. (For bird owners) and former bird owner! It could probably handle being a sand blasting booth with a bit of skin protection added inside, but could be a candidate anyway, or just a real good spray booth for a nice and fume controllable space with exhaust available openings, but as the best thing to keep your printer nice and clean, it rocks, and is made very well! I dont mean to sound like a company sales person, which I am not, but Comgrow are the best people to buy from, and have the most fanominal customer support system that I have had the pleasure to have found, and it started when I read a review just like mine here, and read that someone bought a printer, and needed help, and was really happy to have found them also, and told of their great tech service, and after the sale care, so with that said, I just want to give back as my only other way to show my appreciation for the much needed information that gets you on the right path when you just want to learn what to do when something goes wrong, and will stay with you by staying in touch to make sure you are good to go! Its your dream come true with these folks, and they stand behind their stuff! If I could, I would buy you all one, so you would be hooked up, but I am not quite there yet, LOL, but this one is really a good buy, and just had to tell ya all about it! Thanks and Happy printing folks!

I love this enclosure! It was quick & easy to build, and is quite large for the price. The zipper door goes all the way over the top of the enclosure making for easy access, along with the numerous access points which are velcro-sealed. Its quite spacious & offers more than enough room for an Ender 3-sized machine, if not a slightly larger model even. Definitely grab one if you find yourself in need!

Love all the extra outlets inside, fits my Ender 3V2. I used a plastic hammer to put the metal pieces together. GREAT PRICE!.

I received my second cover after my first one had some issues from some rain forest carriage. after talking with customer service on this directly I received my replacement, it was very quick and after assembly this is a amazing tent for my ender 3 pro. this is very good quality, with amazing customer service.

Its big enough for the ender 3 pro with the large spool on top, once its done printing Im putting it inside it. Looks like a grow tent covered in spandex, works great and has some pockets on the side