Dayton Audio BPA-38G HD Binding Post Banana Jack Pair Gold

(1225 Reviews)

Price
$8.36

Quantity
(10000 available )

Total Price
Share
158 Ratings
138
14
1
3
2
Reviews
  • Matthew Paz

    > 3 day

    As advertised. Sturdy and capable

  • Luther Metke

    Greater than one week

    I dont like terminal cups because they compromise the structural integrity of the box. However with this method you end up with terminals that are not flush with the box wall. In my opinion, especially with car stereos, its important to be able to save space, and having a terminal post sticking out 3/4 anywhere is not ideal. I thought I had out smarted the two downfalls. My plan was to fortify the box wall in a small area on the INSIDE of the box so that it was 1.5 thick instead of .75. I did this by cutting a 2 by 2.5 inch piece of mdf and holding it in place inside the box while drilling from the outside. Wood glue and the terminal nuts do the rest. I drilled through both layers of MDF with 1/4 inch drill bit and then widened the hole on the outside wall to a 1/2 inch hole about .65 inches deep so that the whole post could be recessed into the speaker box flush. Im using banana plug connectors so I dont need access to the knuckle nut terminal part. I did manage to make a happy ending, but I ran into some problems. With my install I had 3 problems. 1. You need 3 drill bits. 1/4 inch, 1/2 inch, and 9/16 inch. I only had the first 2. 2. Glue seeped into the inside of the terminal causing me hours of clean up. 3. The knuckle nut tighteners got scuffed up tapping the terminals in place with a hammer. The first problem was that 1/2 inch will only recess to the knuckle nut. You need a 9/16 inch bit preferably to widen it a 3rd time for the last 1/4 inch of recess. I didnt happen to have one handy and I actually liked the look of it with the terminals sticking out only a 1/4 inch. Im using 90 degree banana plugs so the clearance was good enough for my purposes. I think I might like it better with the initial plan, but I wanted to finish the project that night and no stores were open. . You can make it flush with this product, but you need to double up the wall where the terminals go through, and you need a 1/4, 1/2, and 9/16 inch drill bit. You also need to be careful how deep you go with each. The second problem was unexpected. I dont know about you, but It seems intuitive to me to want to try to use some product to seal the hole during install. I used wood glue. Now if you drilled perfectly you might be able to get a seal without product, but I wouldnt risk it. So I lathered my posts in wood glue before I installed them in the hole. I thought everything was fine until i realized that the glue was pushed into the banana plug terminals filling them up! Basically some pressure was created upon insertion and the glue slipped into the inside of the terminal between the bottom of the knuckle nut and the terminal post. It took me an hour to get it out using toothpicks, paper towels and needles! So when I went to install the second terminal I made sure to tighten down the knuckle nut supper tight to try to prevent this. It didnt work. There needs to be an o ring between the knuckle nut and the rest of the post to seal it when the nut is locked down. Keeping in mind, this only happens when you are trying to recess the hole post, and when using wood glue. If you are fine with terminals sticking out 3/4 inch then this doesnt apply to you. Problem 3 happened because the knuckle nut tighteners are plastic with gold paint. The rest of the terminal is solid material but you do have to tap them into place with a hammer because of the furrowed part of the shaft. The plastic knuckle nut was slightly ruffed up and I had some paint chipping from the process. I avoided this on terminal 2, 3, and 4 by using a paper towel between the post and the hammer while tapping them into position, or you could use a rubber mallet. To be fair, Im doing a custom install probably not considered by the engineers of this product. Most people probably dont recess the post past the screw down speaker wire hole. Im using banana plugs so I dont care about that part. I wasnt able to find anything that included the banana connector part and not the knuckle connector. Even though this product is not perfect for the job and the way I did it, I was able to get a clean install eventually. If you like the way I installed them, I recommend some o rings or perhaps just put some silicon on the bottom of the knuckle nut before you screw it down and then let it dry over night before you install the whole post with wood glue. I plan to buy two more for my other sub and Ill let you know how it works the second go around.

  • Corey Burns

    > 3 day

    I love these for use in a sealed subwoofer enclosure. Good quality and durable

  • Woodworker

    > 3 day

    These are worth the money. They are beefy, nice, looking and work well with my banana plugs. If you care about looks and performance these fit the bill.

  • R. S.

    > 3 day

    Have not yet used them in a cabinet, but the weight, construction, and quality is unexpected at this price range.

  • Adelle Block

    > 3 day

    Very robust construction. All mounting hardware was included even a soldering ring. These are used in a 40+ year old pair of Klipsch Heresy speakers so that I could connect via banana plugs.

  • Agent J

    09-06-2025

    Beats the heck out of those cheap plastic boxes! Drill a slightly smaller hole, tap it in, and you have a sturdy airtight connector.

  • Loyal Lemke Sr.

    > 3 day

    I love these. Every time I build a speaker box i use these. Hands done best terminals ever

  • JZvisuals

    > 3 day

    overkill... maybe... it works.. and looks good doing it.

  • koenigsegg

    > 3 day

    High quality

Quick OverviewThese heavy-duty binding posts were designed with the audiophile in mind. Quality, 24kt. gold plating assures the highest possible signal transfer and resists harsh environmental corrosion. The binding posts can be used with banana plugs or will accept wire up to 8 gauge. Product Highlights 24kt. gold plating for best signal transfer and corrosion resistance 1-1/2" rear bolt mounts in speaker cabinets from 3/8" to 1" thick Large diameter knurled heads enable positive finger-tight connections Knurled shaft prevents post rotation Product Manuals / Spec Sheets / Downloads Dayton Audio BPA-38G Mechanical Drawing AddThis Sharing Buttons Share to FacebookFacebook Share to TwitterTwitter Share to MoreAddThis These heavy-duty binding posts were designed with the audiophile in mind. Quality, 24kt. gold plating assures the highest possible signal transfer and resists harsh environmental corrosion. The binding posts can be used with banana plugs or will accept wire up to 8 gauge. The large diameter knurled head allows for positive finger tight connections. Extra long rear bolt (1-1/2") for mounting in speaker cabinets with walls up to 1" thick. To install, simply drill a 1/4" hole and gently tap the binding post in place. The knurled shaft will keep the post from turning and creates an air-tight fit. Overall length is 2-1/4". Sold in color coded pairs with solder tabs. Product Details Model Number BPA-38G List Price $11.49 Color Gold Unit of Measure Pair UPC 844632018459 Warranty - Parts 5 Years Warranty - Labor 5 Years Product Shipping Weight (lbs.) 0.16 Product Weight -- Product Height -- Product Width -- Product Length 2-1/4" Product Depth --

Related products

Shop
( 2231 Reviews )
Top Selling Products