【EIBOS Official】3D Printer Filament Dryer Easdry, 3D Printer Filament Dryer Box with Fan, Adjustable Temperature, Humidity Control & Spool Holder, Compatible with 1.75mm 2.85mm 3.00mm Nylon, PLA, ABS

The EasDry I received was obviously used. Seriously obviously. It was missing the protection on the clear pane. It was missing the silicon loop that prevents the spool from sliding. I probably spent 30 minutes looking for the silicon loop thinking it was buried in the box. Starting the exchange process. Will update after I receive a replacement.

Dryer quickly heats and dries my filament spools. Has not humidity indicator so I can see how quickly it dries out. Well made and compact. Has hole on top and front so you can run filament thru it during printing

Working as intended so far. Will update if anything changes. Wish the humidity read out had temp also but it doesnt.

This dryer made all the difference and I should have bought it a while ago, like when I bought my printer. Ive always been careful keeping my filament in a moisture free environment but after some of my older rolls were constantly having bad prints I decided to give this dryer a try. The results were outstanding! Simply drying the filament a few hours before printing fixed all my adhesion, layer, and stringing issues. The unit is built rather well for the cost. The preset temp knob handy

Was easy to load a roll of pla+ filament in with the cardboard rolls. Helped solve the problem of the roll coming off the spool of my flsun qq-s. Plugged up right out of the box. May have to invest in another one for my flsun delta next!

The quality of the product is poor. The product worked properly the first time I used it, and after a few days I used it again and he was no longer running. I suspect it is an inferior product.

I purchased this EIBOS Easdry filament dryer to see how it compares to the Sunlu S1 filament dryer. The Easdry is a million times better in every aspect. You get full circulation of the warm dry air by the small fan on the back going over heated elements. With the dryer box sealed air will move around the entire spool. There are small exhaust ports that will let the air escape as needed providing moisture to escape instead of holding it like the Sunlu S1. This is not some glorified food dehydrator at all. as you can see in my pictures there is a dial to provide the right amount of heat needed for each type of filament. There is a meter that gives you the humidity inside the dryer. I cant tell you if it is 100% accurate but it is still nice to have. The panel opens up with the pull of a really unique string / latch system that keeps the box sealed very tight to keep the warm air in and circulating. You will see in my pictures a cone that sticks out inside the box with small vents and elements. This is where the air comes in from the fan on the back. I also posted a picture with the power specifications if anyone needs that information. My dryer was 110V AC power as I do live in the United States. The Easdry comes with a power cable not a power brick which is something I really do appreciate. There is also a bowden tube that is about two feet that comes with the filament dryer. It can be put into one of three rubber grommets located on the top, front and opposite side from the front so you can print with your filament while you are drying it. I really like this filament dryer a lot. Im going to place an order for a few more and will be selling my Sunlu S1 filament dryers. I hope you enjoyed my review and I do apologize if it was a bit long. I was not paid or asked to make this review. I also purchased the filament dryer with my money.

【EIBOS Official】3D Printer Filament Dryer Easdry, 3D Printer Filament Dryer Box with Fan, Adjustable Temperature, Humidity Control & Spool Holder, Compatible with 1.75mm 2.85mm 3.00mm Nylon, PLA, ABS - $52.99 at time of review. It works and works well. Has a simple humidity monitor on it. Would have been nice if it was backlit. The side panel cover is a nice double walled design to keep in the heat. The heater element itself is a good design to spread the heat throughout the entire case indirectly unlike some heaters out there. There are 3 holes, one on the front, top and back so you can feed your filament out based on how you have the dryer setup next to your printer. They provide a nice long bowden tube which can be moved to any of the holes you desire. And one thing that others lack is stability! Its wider and keeps it from tipping over. You dont need to remember the temp to set it at for each material as it has it labeled on the simple temperature control knob. Definitely prefer that over the digital settings. Really, the only lacking feature on this is a timer to auto shut off. The EIBOS sticker on the side bubbled up on first use when drying PETG. No big deal, but kind of odd they would put a generic sticker right where the heat blows on to.

As another reviewer mentioned and I didn’t catch until I received it, this is the EIBOS Series X: Easdry filament dryer. I have multiple 3d printers and multiple filament dryers and they range from okay but needs improvements to the (almost) perfect. The EIBOS Easdry falls into the (almost) perfect category! The design is (at least as far as I know) a unique design for filament dryers as most that I have seen are either a half clamshell with a top portion that is hinged and opens to insert the roll of filament or one with a clear boxy top that you lift off and set the roll of filament in on rollers. The EIBOS Easdry has a clear side that locks into the unit, and you remove the side completely and place the roll of filament inside on a center mount that the roll rides on. I want to note that it does take some effort to pull down on the pull cord enough to remove the clear side piece. I do like the design and the look, but the side load design does lead to one issue that is important enough to mention and deduct a star over. Unlike many of the other filament dryers out there that have the filament roll resting on bearings, the EIBOS Easdry has the center of the roll rest on the center post that sticks out in the middle of the dryer. This means that with the weight of the roll resting on the plastic, there is enough friction to keep the roll from moving easily and rolling smoothly. I was planning on using this dryer with my Direct Driver Ender 3 S1 Pro, especially since there are multiple outlets for the filament so I would be able to use the one located at the top and just have it feed through some Capricorn filament tubing to go up and over a filament guide I 3d printed so that it could feed into the direct drive extruder and hotend. I discovered that there was quite a bit and possibly too much friction and tension with the filament (the filament roll I was using is a think cardboard which may have contributed to the issue and a plastic roll may move easier). I will, however, be able to use it with one of my Bowden printers where the path is shorter with much less of a curve. I believe that a simple fix is possible by using two large diameter bearings and a cylinder that the roll would sit on. The rest of the Easdry filament dryer is great, from the dedicated desiccant compartments, very quiet fan (so quiet I didn’t think it was turned on), multiple filament outlets, and easy to use temperature dial. The other filament dryers I have all have some sort of screen (whether a simple LCD type or a detail filed touchscreen) so I wasn’t sure how I was going to feel about one with no screen and a single, simple dial to control the temperature. I have to say that I really like it! It is simple yet very effective and it does exactly what it needs to do, change the temperature based on the type of filament you need to dry. You just load up the filament, close the side door and set the dial to the correct type of filament! Even with the issue of the roll sitting on top of a plastic surface instead of some type of bearing to allow it to roll easier, it is a great filament dryer. It looks good, dries the filament extremely well and is easy and simple to use. I can and do recommend the EIBOS Easdry filament dryer!

I like this dryer. It is compact and super easy to use. It has a fan which is nice. I have been using the Sunlu S1 which works pretty well but does not have a fan. I have multiple printers so it is nice to have multiple dryers. If I have older filament, I run it before I print to dry it out. I run a dryer every time I print now. (either one) I think that a dryer is a good upgrade to print quality. I have better luck with tricky filaments and adhesion since I have been using a dryer. (not a dramatic difference but a difference) This is a little easier to use than the Sunlu but not much. It is a little more compact too. I like that this dryer has a fan. The price is good. It works well and is pretty simple.