ELEGOO 6.08 Inches Monochrome 2K LCD Compatible with ELEGOO Mars 2 and ELEGOO Mars 2 Pro Resin 3D Printers with 1620x2560 Resolution, Active Area 3.25 x 5.14 inches

I was a little nervous having to install a replacement screen as I had never done it before but the videos that they have is great and the install was super easy. I think the hardest part was getting the old (original and damaged) screen off.

My FEP ripped during a print and ruined my old screen. Glad I could find a new one on here.

Some of these do not fit flush on a Mars 2. Keep the defective parts, unlike what I did, and then you can use the glass piece from the defective part to place, and thus make the LCD area fit flush. Apparently, it doesnt really do much (maybe it helps to protect the actual LCD part) so theyre reusable.

Instructions were a bit unclear and I wasnt aware of the glue securing the old screen so removing it was quite difficult. The screen I received was faulty. However Elegoo customer service got back to me very quickly to troubleshoot and replace the screen.

I have owned my Mars 2 Pro since its release last October. Im on my fourth LCD display panel. Prior to it becoming a consumable part on Amazon, it would take a month or so each to obtain from Elegoo, but they replaced the LCD each time under warranty, thank you. The LCDs have a soft polymer layer that is critical to the LCD function, its not just a protective cover. When I installed LCD#4, I placed it under the gorilla glass plate. Now the LCD polymer layer is protected by glass that can be scraped off if you have a resin tank failure and resin gets polymerized on the surface. I see no difference in my part quality. About a third of the box of parts were printed since LCD#4 was installed.

*Direct replacement for voxelab proxima printer. *It fit into place and came with blackout sealing tape for the perimeter. No need to use any foam tape, installed flush. *Prints as it should no DOA pixels. *Well packaged arrived in good condition. *Decent price.

Excelente para la creality ld 002h

Perfect OEM replacement for the Mars 2. Installation was a breeze. I spilled resin on my LCD screen from a hole in my FEP and when scraping it off I accidentally scratched my screen. I ordered this replacement and it shipped fast and came in a hard cardboard protective packaging which included glue strips for the LCD and a replacement gasket. I used the video tutorial from elegoos website and it was very easy to do and the finished install looked just like factory. Powered everything on and tested the exposure and it all worked fine. I will mention however, that on my printer, the old screen did not survive the removal process - I thought I might keep it to use as a backup spare just in case, but the screen cracked when separating it from the adhesive strips. Make sure to take your time and clean up all the old sticky residue from the previous gasket and adhesive strips before installing the new gasket. IPA works fine for this. If youre really keen on trying to preserve your old screen, you can likely take a hair dryer to soften the adhesive strips before removing it.

As a replacement screen for my Mars2 pro this is not the correct thickness in the picture the one on the left is the original and the one on the right is the replacement. Half as thick. Other picture shows it sitting in place on the machine and it does not come up close to level with the surface. The gasket would not even reach the screen when putting it on. Not usable. Very disappointed. Sending it back. After a little research I found the correct way to install the screen, I just needed to take the bottom glass off the old screen and mate the new one with it. My mistake although this could be put in the packaging leldetting you know this. I will say the ven#or reached out to me quickly and I am making sure to note that as it can be rare for this to happen. I will order replacements from here in the future.

My previous screen wasnt having any major issues but had a little bit of hardened resin on it so I wanted to swap it out with a new screen while I was doing maintenance When I swapped out the new screen it now fails the exposure test and only shows the horizontal lines and not the Elegoo logo. :( Ive cleaned the connectors, verified it was installed correctly, and any post I find online with a similar outcome says either the screen or motherboard is failing. Ive absolutely loved my printer and hope this is just a 1 in 100 fluke