Hole Saw Kit, SUNGATOR 5-Piece Set. Specially Constructed Heat Treated Carbon Steel, High Precision Cutting Teeth. Cut Clean, Smooth, and Precise Holes Through Wood, Plastic, PVC Board and Drywall.

I used this to cut a hole in a sink and it work very well .

Before purchasing these holesaw’s I had never heard of this company but I figured for the price I would give them a try. I was pleasantly surprised, these saws are extremely sharp and cut through wood very easily. I have even used them to drill through the steel back of my toolbox, I don’t even know if the saws are rated for metal but they did cut it without dulling the blade. I have been very impressed with these and if I manage to dull or break them I will buy them again.

I read many reviews, and I went for it. There are cheaper sets, however I liked the case design so I went with this. I used the 1-1/4 bit a lot making holes in plastic 55 gallon drums for a rain barrel project. One of the reviews mentioned that they needed a socket to remove the arbor from the hole saw bit. I hope that person hit it with his purse fist, that usually loosens them. Here is an easier way, remove the bit, loosen the grub screw, then put a smaller screw driver through the side holes and remove the hole saw bit. Not hard right? That is because its not hard! Are there better bit locking designs? Yes, in this kit when you use the larger arbor its an easier design to remove it. Some reviews you need to understand the authors skill level.

I bought this to drill holes for plastic grommets for my desk to try to better organize my cables and not have to stretch them over the edge. The desk is typical engineered particle board and I wanted a reasonably priced hole saw for this. It works and does a nice job overall, but it takes a lot of patience to cut through even marginally thick engineered wood. I dont know if the saw blades will old up over time, but it works if you have patience. I also found the 2 hole saw still made a slighter bigger whole than the 2 grommets I bought, but it wasnt a show stopper for my project. I drilled the pilot hole first and then started the hole with the hole saw on both sides hoping to prevent splintering on the underside/inside of the hole and that worked well.

I purchased this item to cut a hole in a 1/2” round wooden board to to use as a small umbrella table for my patio. The product does not come with directions, however, it was fairly easy to figure out, and Im in my 60’s. Worked perfectly and Im very happy with the result.

Bought this to fix the previous plumbers laziness. Had to poke a hole though a 2x4 then 1/2 osb and as all home improvement projects go just a sliver of floor joist. Mounted the size I needed chucked it up on the trusty 20v lithium drill and let it eat. Cut through the 2x4 like butter. Once I got to the osb we were making heat like jet engine exhaust. Pop through the osb and find that edge of the joist and thats when the going gets tough. See between the osb and 2x4 I had some high quality 1997 era linoleum, super heated linoleum makes it near impossible to remove the slug you just cut. This is where I have issues with the tool, everything prior is my fault and the previous guy who took the easy road. I took the saw off the chuck, mind you its somewhere between 150 and the surface of the sun in temp. Once I clear the mess and go back at it the nut will not stay tight, had to let it chill on the window sill here in the December midwest to finish the job. Overall it worked, 2nd hole was just osb so that was a walk in the park. For what you pay it does well.

Was very easy to use

The set does everything I need it to do. I have cut the 7 holes I needed to get done, and they all went easily. BUT... like others, I wish the smaller pilot would fit a 3/8 drill. Like others, I had to use a 1/2 drill for every hole, whether the small pilot or the larger pilot. So it missed 5 stars throughout simply because a few thousandths on the small pilot made me use a much larger and heavier drill to drill a 3/4 hole. The saws cut well... low speed, cutting oil for the metal, and no discoloration or loss of edge that I could see.

Used to drill holes in kayaks for rod holders so I didnt need anything expensive. Did the job!

Needed to drill some hole of a couple different sizes in some plastic/PVC pool equipment. This little kit works well, and is super affordable. No complaints.