MUSETEX ATX PC Case Pre-Installed 6Pcs 120mm ARGB Fans, Mid-Tower Computer Gaming Case, USB 3.0 Tempered Glass Phantom Black Computer Case, MN6-B

Case is great for the price and all that is included. I moved the front fans to inside the case because I couldnt believe that they would pull much air being pressed against the front glass. If your motherboard has heat sinks on it, like the ASRock B450m Steel Legend, you will have to remove the top and back fans to install and it will be tight. One more tip make sure to run your motherboard 8pin power cable, if its at the top, before installing the board.

I should have looked closer before I bought it.. It is a very nice case though. I still have it, no sense in sending it back, as I just used a USB DV burner plugged in to a USB plug on the top of the case! Just no slot for it!

I wanted to go cheap and so I bought this unit and although the price was right, I ended up paying for the discount in general nuisance of putting my system in it. They claim it can accommodate an extended ATX motherboard, and technically you can get one in there, but not with all its needed mounting points. I had to drill in my own mounts to make it work and then realized that all the screws were METRIC rather than the regular SAE mount threading. The RGB feature for the fans is fun but not consistent. I can turn it off or chose a color and then the next time I walk by its back to RAINBOWS again. Mounting any kind of hard drive is a nightmare if you use an extended ATX MOBO and there is no hardware for mounting one in front of the power supply. Air-flow through the front is horrible and so I ended up removing the front glass and open grid and put metal guards on each of the 120-mm fans. After fighting with it as much as I had to, to make things work I had grown to loathe this case even though it isnt THAT bad. It just isnt that good....but it was cheap.

Decent cooling, sweet RGB. I have only two problems with it. It is a little small so modern GPUs do not fit. Please check dimensions before buying! Also, if you leave the front panel on, it doesn’t cool well enough. Removing the front glass and exposing the 3 fans does the trick though.

Mounting SSDs to case is a pain, almost requires a 2nd person to hold SSDs while you screw it in, almost being the operative word. aRGB controller is built in to case in a way that makes connecting cords to case mounted SSDs a hassle. Neither complaint prevents you from installing what you need, just makes it harder. Once those are handled it is smooth sailing. A very nice case. Would recommend.

This case could be just a bit taller it was hard running the cables to the top of the motherboard from the top there is not a lot of room and if I was just a bit taller you could fit a 240 rad in the top but its just to short. I had an issue with the argb fan controller and customer service took care of my problem and shipped me a new one hassle free

Got this case recently! Absolutely loved it was easy to install everything and was so excited as this is the first one Ive build from scratch. I turned everything on to make sure everything worked properly before putting the glass side panel on. Once i verified everything was working and good to go i powered everything down so I could put the side panel back on was working on lining up to holes for the screw and suddenly the glass completely exploded everywhere! I never bummed hit or pushed on it. It just completely shattered. Im really bummed out. Update: contacted the seller and they have been really helpful! They are sending me a new side panel and have taken every step possible to make sure they sent me right panel. I havent received it yet but will update once I do. Update: wow guess I forgot to update again. I received the side panel and it was wrapped great! Was able to get it unwrapped and installed with no problems at all! Great customer service!

Well, it was very tricky to mount a MSi Z490 Tomahawk motherboard to the case. The board seemed to barely fit in and required me to remove the case fans from the top of the case to even get close to sliding in the board. Granted I installed the CPU cooler first but it would have been just as hard with it removed. Removing the motherboard also required removing the case fans. This makes building modern parts into it difficult. I first built this case with an older H81 motherboard that was half the length and I was able to slide that in and out without issue. Upgrades got me to 10/11th gen and it was a hit or miss experience. Another issue is the front glass inhibits airflow. When the front is removed there is a noticeable change in airflow. Only the exhaust on top and power supply is filtered. The power supply filter is low quality. However, I really like this case. The remote works great. The RGB button works well also. 6 fans included, cant beat that. Overall, it definitely deserves 4 stars. What a great looking case. Just has a few minor flaws I can overlook.

Pros: - Case material and glass feel and look high quality - Fans work great with very little effort to use fan controller - Case buttons and USB ports/Audio work great! - SSD mount looks cool (to me at least) Cons: - PSU area becomes a really tight fit for cables if the cables are a heavier type, or braided. - Top case fans get in the way of most ATX boards, requiring you to remove them to get the board in safely. I was able to add the fans back later though - You may need to remove some fans to add an AIO cooler - Reset and power jumpers sit loose on the motherboard - I wish the system kept my LED preference on boot (minor nitpick. I have to change to the color I want each time I boot) Over all a great case, but keep in mind some of the alterations you may need to make. Most of these are minor nitpicks, but I feel like space for PSU cables, and loose jumpers on the board (they fall off with a slight touch, but sit fine in a complete build.)

So to all the people saying this case doesnt ha e room for water cooling... see images of mine with water cooling. This is a good case for 90.00. Comes with 6 fans and an rgb controller that you can change with the included remote or with the switch on the top of the case. The 6 fans and controller are worth 50.00 by themselves. They are quiet and push a fair amount of air. I have a Gigabyte z590 elite ax board which has a larger than normal header on it and I was able to fit a cooler master ml120l cooler with zero issues. It can fit a 250 cooler up top but it will cut off your accessibility to some of the plugs on your mobo so it would definitely need to be installed last. There is ample room for wires and enough ports to get the wiring clean so it doesnt look like my first PC with wires everywhere. It has enough room to add up to 3 ssds and a couple hdds. Granted it is tight under the cover and around the power supply but you can definitely get all of it in there. I am currently running an nvme, a sata ssd and a Sata hdd. I will be adding another Santa ssd and 2 more nvmes and I have no concerns for space. The thumb screws holding the glass panel on mine needed a little tweaking I am not sure why they werent okay, but it was a simple fix that literally took about 10 seconds. I would recommend this case for sure, imo it is good enough quality to last several years and isnt a million dollars either.