SUNLU 3D Printer Resin, 1kg Fast Curing Standard 3D Resin for LCD DLP SLA Resin 3D Printers, 395-405nm UV Light Curing 3D Printing Liquid Photopolymer Resin, Low Shrinkage, High Precision, 1000g, Grey
-
Jovanni hiscox
> 3 dayA lot more bang for your buck
-
Tony Toepfer
> 3 dayWorks as advertised, but for some reason either uses more resin for the same amount of printing as compared to any cubic water washable resin, or the bottles dont actually contain a full liter.
-
ME Merit
> 3 dayI purchased this resin because I liked the clear materials. I printed a handful of items so far and these materials have worked out perfectly. Ive used 5s exposure for the main layers and havent had any issues connecting to the bed, layer to layer, and print removal. The odor isnt terrible and I find it more bearable than the anycubic eco resin and the basic resin that I have. I will definitely buy again but will likely try an opaque material instead of the translucent.
-
Philip
20-11-2024ODOR: Much better experience with this one. With the Comgrow, I could smell it once I started going upstairs to my 3D printer room. SUNLU has a very low odor, something similar to Phrozen or Siraya Tech. Every resin has a smell, and this one is lower on the spectrum of being too much. 7/10 STATS Density- 1.11-1.15g/cm3 Bending Strength- 40- 60Mpa Viscosity- 100-300cps Tensile Strength- 30-50Mpa Hardness- 72-88D Shelf Life- Not Given Elongation- 10.002 +/- 10% Body Shrinkage- 3-5% Wavelength- 405 UV Light Printability Okay, the color is closer to a white than grey, until you cure it, then its closer to grey, but still whiter than most greys Ive used. Once this resin was dialed in with the Cones, I was down to a 1.75 second per layer cure time. After printing some models, this was adjusted to a 1.8 seconds per layer just to make sure there was enough strength between layers to prevent any separations between layers. Details are crisp and clear. Supports slip off like a dream. 9/10 Curing Time For our testing, 8-9 minutes was our standard curing time in our Anycubic Wash & Cure Plus. After curing, the resin appeared and felt solid as if the model was cast in plastic. Smooth as butter. 9/10 Dimensional Accuracy and Shrinkage For this part, we ran the new RP tester from Phrozen. I was shocked to see that everything printed, even the tiny little hairs, though, if you have meat hooks like mine and arent careful, youll snap these off, which do so, so cleanly, youll think they didnt print at all. Dimensional Accuracy before printing was spot on when measuring with calipers. Shrinkage was well within my specifications. Larger posts on the RP tester seemed unaffected, while smaller posts were accurate within 0.03mm. 9/10 FINAL THOUGHTS This really surprised us. Going into these tests, I was hopeful, but was more than willing to just let the resins speak for themselves. This one is above and beyond way better than the Comgrow resin. Low odor, no dyes that dye your IPA, Shrinkage that tests better than some of the more expensive options out there, and a cost that doesnt break the bank. They seem to have a bundle deal on their website that pushes the cost down further. If you order 5 bottles, its $99, which takes the cost down to $19.80/bottle. What I ordered from Amazon appeared to be a round bottle. What I got was closer to a flat bottle akin to an oil bottle. This was fine and reduced the form factor on my shelf. Curious though, did Amazon send me the right bottle? A damn fine alternative to more expensive options. 8/10
-
M
> 3 dayI wanted to get a transparent resin that was not as expensive so I wouldnt feel bad about failed prints while learning (and so i can see all the way thru the objects) & this has worked perfectly! no odor when the machine is covered by the UV hood
-
Fred L.
21-11-2024Good finished product but has a much higher odor than other resins i have used and requires a lot more mixing than others as well. Seems to have an odd marble like color swirl to it when pouring out of container unless container is shaken an excessively long time to mix (5-10 minutes)
-
ben zion chen
> 3 dayGOOD
-
Donny Wisoky V
> 3 dayGreat quality, great price, great goo!
-
Male Perspective
Greater than one weekThe resin works really well. I make small parts and they come out prefect. I have not had any issue with these products.
-
Tmoney
Greater than one weekThe cure time for the resin is nice and quick. My only complaint is after fully curing the models are bit more brittle than other resins, this is a worth while trade off, supports break away cleanly and this resin is nearly half the cost.
