Thermalright Intel 12th/13th Generation LGA1700 Anti-Bending Buckle,CPU Stress Bending Correction Fixer, Curved Pressure Plate,Fully Fitted and Fixed Without Trace Installation (Black)

I was a little nervous about installing this at first, but it was surprisingly easy. I placed it on my 17-13700K CPU and I noticed my temps went from Mid 40s to high 30s while in windows, and when running Cinebench I went from low 90s to mid to low 80s. Overall highly recommend if youre comfortable with taking apart your computer. Takes less than 10 minutes.

13900k/Liquid Freezer II 360/Z790 Aorus Master - no improvement in temps unfortunately. Well built and easy to install however.

If you have a 12th or 13th gen processor, this is a must have. I installed this frame on two different computers and it dropped temps by at least 8 degrees on each. Install is super easy if you follow the steps in the Gamers Nexus youtube video.

I didn’t notice a change to my thermals, but it makes my install look cleaner

Installed this on my Asus Maximus Z790 Hero with no problems. Used factory screws from motherboard and no issues. Make sure to tighten in criss cross pattern to make sure it tightens evenly and doesn’t bend. Highly recommend as this also lowered my CPU temps on my 13900k

I honestly did not watch the review of this plate on Gamers Nexus. I did watch Steves review of the Thermal Grizzly one though but when I saw how much it was going for I was like NOPE. I thought well lets spend $12 and if it sucks then Ill buy Der8auers. I love the lil German guy. Honestly I just slapped this one on. Didnt do all that putting marks on the screws and slowly tightening it down like Mike did. Temps were lower than the GN reviews so I guess I slapped it on my 13900k right. I am using a 360 Lian Li AIO though. So go ahead and buy it. If you get something different then you may need to remount it or have one that may be out of tolerance.

This product didnt reduce the temps too much, maybe 5C at full load. However, I got this product for the longevity of the CPU health. This way I can guarantee CPU bend doesnt happen over time.

Fácil instalación (tienes que ser extremadamente cuidadoso) se instaló con un procesador y motherboard nuevo, ayudó bastante en las temperaturas

This is my first build in 4.5 years, so this time around I wanted to do tons of research. Im installing a CPU water cooler for the first time ever and researching that a fair amount led me to these CPU brackets. Ive never been satisfied with the cheezy, light weight CPU brackets/fasteners which come standad on MBs. This seemed like a valuable asset for just $14. Im running a 13th Gen Intel on an MSI Z690 ACE MB. As you can see from the pic, the fit looks very clean and the aluminum bracket is well machined. I do not know if temps will be lowered vs the stock guillotine bracket but it sure holds the Intel in place far better. And that can only be good.

Las nuevas generaciones de Intel tienen la característica de llevar temperaturas elevadas, además que el Bracket instalado para soportarlo en la tarjeta madre ejerce una presión asimétrica del CPU a los Pines, esto ocasiona que con el tiempo las temperaturas hagan un Ablandamiento en la superficie total del CPU, no habría problema si el bracket que soporta al CPU ejerciera una presión simétrica sobre la superficie comoleta de éste, sin embargo las áreas con altra presion comienzan a doblarse sobre aquellas que no cuentan con la presión suficiente, al momento de instalarlo fue super sencillo, las temperaturas de mi i7-12700k no superan los 35 grados en tareas simples y a máxima exigencia no supera los 71°C, es una inversión muy buena y prevenir el daño sobre una pieza tan importante como el cpu vale la pena.