Wall Switch, YoLink 1/4 Mile Super Long Range Smart Light Switch Single Pole 10A in-Wall Switch Compatible with Alexa Google Assistant Home IFTTT, ETL Listed, Neutral Wire Needed, YoLink Hub Required

I was able to wire and install this switch in a 4-gang box. Since then its been turning on/off my outside lights as I programmed. Programming the switch and checking when it turned the status of lights is very easy. All yolink products are very simple to setup, and use. They are also very reliable and never failed since Ive been using them for almost a year. I wish they had more products such as indoor/outdoor cameras.

I really love the yolink ecosystem. they are super easy to add to the system, so i was excited to migrate from my zwave switch that controlled my outside garage lights to this system. Overall it works and does what it is designed to do, but i do have a few minor issues i hope they address in future light switches. 1) As most others have noted, the red LED light is sort of annoying. I have it in the garage so it isnt that big of a deal, but i would not want these throughout the house in main living areas. THe red indicator light when off is just very bright and annoying. I would rather it be a very small led indicator in the bottom corner. Or if you could change the LED maybe a different color would be better, and/or brightness level. if that was controllable. When on it is white which is fine. 2) The overall feel of the switch is not the best i have seen. Where you make the connection for the electrical, the screw is what bites into the copper to hold it in. It does make a very secure connection when tugging, but most other switches have molre of a plate that squeezes the cable on the inside. Again it seems to be ok but just something i noticed. 3) My switch came with the arrow facing down (opposite of the instructions which tell you to have it facing up). Support noted it was fine to install, but again just noting that it was not what the directions had. 4) THe switch housing is a little thicker than the other traditional switches, so i think my cover plate was not fully flush on the one side. i took a picture so you can see although it may be hard. Id rather it be designed more like a traditional switch and if needed be able to tear off the ears as some setups do require that. 5) I would have loved if this was an energy management capabilities to keep track of how much power, but not a deal breaker, especially at this price point. 6) The software does have sunrise/sunset scheduling, but i am hoping they include more advanced such as x minutes before and x minutes after to tweak my settings a little better for my needs. Again overall i like it and great price point but hopefully they address some of these in future models.

Wevard using these to replace some no too reliable X10 switches . So far so good.

I installed two switches for overhead lights in my workshop that is located 300’ from my house. These switches are on opposite walls, requiring crossing the shop just to turn on/off lights. I also installed a YoLink Motion Detector over the entry door. So now when you enter, the overhead lights come on and stay on as long as there is motion inside. This is great as sometimes, I’m going in and out several times a day. I can also use the app on my phone to check the status of or turn any YoLink device on or off. Plus I can get notifications on my phone if the motion detector senses anything.

Over the last few months finding out and learning about yolink products I ordered several wall Switchs and installed one in the bath room and two in the garage. They work perfect! In the garage removed my existing switch and installed a yolink one. I was able to set the switch to auto turn off after 5 hours of it being on (seeing that i am very seldom in the garage longer then that in one setting and at least if the lights are left on over the weekend it will get turned off automatically). Then I installed a second yolink by the other door into the garage. The second switch is just power to the yolink switch only it does not control any device. I then did Direct 2 Device pairing of both switches. I had to do this trice. One Pairing one direction and then paired the switches in reverse. By doing this both switches stay in sync so when I turn one on the other also goes on. And the same in reverse when one goes off the other goes off. All of this was done without the need of internet or even a yolink hub. Now I also have the garage door sensor for both of my garage doors. I then configured some automations and settings to track the garage doors open. If one door opens then the lights come on automatically. And if both doors close (and both have to be closed not just one) the lights will then go out! Then the I installed another switch in by bathroom to replace the exhaust fan switch. I also place a temp / humidity yolink sensor in the bathroom. Now when someone takes a shower and the humidity gets above say 90 the fan kicks on automatically! And turns off once it drops down again. Its magic! But if someone just needs to use the restroom and they want the fan on they can manually turn it on and off like normal.

I just like Yolink products. Every one I have just works. They are easy to install and do what they are supposed to do. I started with their leak sensors and the hub. They work great. Then I got the smart plug. Love the functions and it works great. Now I have the switch and it works great. It was easy to install. Turned off the breaker and took out the old switch and this one just went right in even easier than the conventional switch I replaced. It integrated easily and perfectly into the hub and the app. Came right up. No connection issues. Nothing. It just works. I love the timer functions which make it a set and forget device for me now. I will be looking into getting more of their products and I will be buying more of these switches.

I recently installed this light at the opposite end of my home from the hub, and the response time is excellent. I called customer service to figure out if the red LED light could be turned off, and a human answered the phone on the second ring. Excellent customer service. The only complaint is the bright red LED light that activates when the switch is off. I was able to pop off the front of the switch and cover the light with a small piece of black gorilla tape. Problem Solved. I will be first in line to buy when they come out with a dimmer light switch.

Quick and simple installation.

First, let me say Im a huge fan of YoLink devices. I have 18 sensors and alarms around my house. I purchased this switch to go with a motion detector. The motion detector was less than stellar, and I left a review for that. The YoLink switch replaced a similar Kasa brand smart switch. The YoLink switch is decent, but not quite as nice as the Kasa switch. It installed easy enough, and is SUPER easy to link to your app. The overall feel of the switch itself is simply a little cheaper than what Im used to, when comparing it to Kasa. The part I do not like however, is the red light in the switch button when the switch is off. This switch is in my basement, so I can live with it, however, I will not be adding these to my living room or kitchen until something is done about that light. It looks cheap, and its bright when the room is dark. I understand that some folks might want a way to find the switch in the dark, but Im not a fan. Perhaps if YoLink added a way to control that red light from the app? Overall, not a bad product, but it could use some refining.

When paired with motion sensors (or manually /w smartphone), my switch is part of an electronic team to (among other things) light/darken zones as people/things move through. Exactly what I needed.