Creality 3D Official Ender 3 Bed Upgraded, PEI Sheet Removable Magnetic Flexible Heated Bed Plate Build Surface Bed Cover for Ender 3 S1/Ender 3 V2/Ender 3 Pro/Ender 5/Ender 5 Pro 3D Printer 235X235mm

Bien producto aún que si trabajas en el con TPU lo vas arruinar, también se debe tener cuidado de retirar el PLA con la cama totalmente fría si no lo arruinas

Good quality

I had several issues with adhesion for my prints. This bed fixed all the problems. Don’t forget to adjust your z-offset after installing it.

This is definitely a step up from the stock build plate on the CR-10S Pro V2, however, I had constant issues with prints warping. My printer is only a few months old and Ive testing different things. I had installed a Wham Bam and wanted to try this one. I suspect that this plate doesnt distribute the heat effectively - Using a laser thermometer, I tested various areas and the temperature was 5 degrees less than what it normally should be AND fluctuated about 5-7 degrees depending on the area of the bed. I tried different things - temperature offsets, increasing/decreasing the temp, raft sizes, etc.. nothing solved the warping. Ended up returning it.

Literally the first print on a Creality printer, with a Creality bed using surprisingly the Creality PLA. Used 205 degrees Celsius on the hotend and 50 degrees on the bed. Print stuck well but even though leaving on the printer for maybe a half hour past hitting ambient temp of around 24-26, it didnt simply pop off like other say it should, or like it does on the textured PEI bed that I have. The fact that this is just a sticker is what makes it not worth it, from what I can tell most of the smooth beds are just that. Hopefully the pictures do it the injustice it deserves. It wasnt even the hardest print ever to remove, it took a little bit of tugging but, wow. Not only bubbles that were on the very perimeter of the print, but it seems there is a raised lump going all the way around it as if when I pulled it off it raised it enough to delaminate it and cause bubble sporadically to appear but also a line that will more than likely bubble up in the prints to come.

Cleaned bed to help with adhesion. After lifting and warping. Bed is still lifting and warping. Never buy this bed.

Im using a new Creality Ender 3 Max Neo. **No need to apply the magnetic sheet** When I got my PEI sheet I was very apprehensive about applying the magnetic pad, which uses sticky adhesive on its backing to fasten permanently to the heat bed. If it didnt work as intended I would be stuck with a magnetic mat on my machine. It would very difficult to remove it, and clean off the adhesive (if at all possible). So I didnt use the magnetic sheet. I simply removed my glass plate and swapped in the gold spring steel PEI directly onto the heat bed. Its about half the thickness of the glass bed so I shoved a small piece of cardboard under each plate clip and it held snug. Of course, the bed needs to be manually raised a bit first to compensate for the thinner plate. To ensure that the PEI was laid perfectly, I positioned the printhead at all corners and the middle, measuring the distance with a sheet of paper (the paper should slide between the printhead and the plate with just a bit of resistance). Then I auto-leveled the bed. I have so far printed a dozen models, and they all held firm and printed perfectly. The best part... they popped off the PEI sheet with no effort at all. I didnt even need to remove the PEI and bend it. Bonus - not using the magnetic sheet allows the PEI to warm faster because it isnt insulated from the heat bed. And without applying the permanent magnetic sheet, I can easily swap back to the glass bed without the magnetic sheet insulating the heating process. After years of struggling with not enough adhesion, then way too much adhesion - its a dream come true.

The PEI Sheet pulled away from the steel sheet when removing the print. Highly disappointed and looking to purchase a glass bed in the future.

This one has major adhesion problems; even after cleaning it with 99% alcohol to make sure the surface was totally free of any oils, debris, etc. The only good thing this one has going for it, is that its a sheet of steel, so its magnetic. Get the smooth gold colored one instead - it doesnt have the same problems this one does.

good packaging, nice quality