Creality 3D Official Ender 3 Bed Upgraded, PEI Sheet Removable Magnetic Flexible Heated Bed Plate Build Surface Bed Cover for Ender 3 S1/Ender 3 V2/Ender 3 Pro/Ender 5/Ender 5 Pro 3D Printer 235X235mm

Out of all the magnetic plates I have used. This is my fav.

Easy to install and wonderful adhesion! Removing a star because after several prints (varying lengths of time and various locations on the bed) there are tiny tiny bubbles showing up in a couple spots. These mostly don’t seem to actually be bubbling above the surface / affecting the smoothness of the bed so that’s good. But it seems weird to be happening so quickly and I’m not sure if it will stay a purely cosmetic issue. If it stays like it is, I’d definitely buy again though. Context: I exclusively print with Inland PLA+ and have the bed about 60C

I was surprised how well my prints have stuck to this new material. I have been using a textured glass and that still needed hairspray to stick. The PEI has been great so far without anything extra. I love how easy it is to remove the print. Either flex the plate to pop it off or let the bed cool completely and it slides off.

Cleaned bed to help with adhesion. After lifting and warping. Bed is still lifting and warping. Never buy this bed.

Replaced the original textured pei plate that came with my Ender 3 S1 Pro with this one and have had no issues. Washed it thoroughly with warm soapy water, scoured it slightly with the scrubber side of a sponge to rough it up a bit and started printing. No need for any kind of glue or adhesive and just wipe it down with IPA every couple of prints. Prints stay firmly attached during printing and pop right off after the bed cools down. If I remove a print with the bed still warm, I just pop up the flex plate a bit and the print releases fine - not too much and not too little adhesion.

Worst PEI I have used.

The adhesion on this is unbelievable for PC, PETG, and TPU. PLA is pretty good as well but this surface is great. I damaged mine by thinking it needed as much squish as my textured PEI flex-plate. It pulled dents in the build plate with how well it stuck. Totally my fault and would buy again. Probably will.

I bought this to replace the coated bed plate that comes with the Creality Ender 5 S1. Unfortunately I can’t get any prints to stick to it. I’ve tried wiping it down with isopropyl, slowing down the print speed, increasing the bed temp, and a combination of those with no success. I’m using Creality PLA filament, which provided great results previously. No other printer settings were changed. Not sure what it might take to make this work, but for now I’m stuck.

After buying my Ender 3 V2, it was printing fine in the beginning. Then I started to get the adhesion issues, which I initially could solve by washing the glass panel in the dishwasher, then dishwasher with alcohol cleaning. In the end nothing was sticking anymore, and elmers glue was the only option left. Since I had good (initial) experiences with the glass platform, I decided to buy a new one. I went through the same struggles, but then I had a PETG print stick to it with a vengeance. So that one became a write off too, since I damaged the glass. After reading a lot of articles online, I decided to give a PEI sheet a try. So I glued that one to the scratched plate, and it worked fine. However, larger prints were sticking too much.... The PEI was by itself very good though, so the obvious next try was this flexible bed. I can only say that I am very happy with this purchase. I can recommend this upgrade to anyone who just bought their printer. Great adhesion, and very smooth. So your prints will be very smooth too! What I do is clean the platform every single time before use with 99.9% IPA, which I have anyway for my resin printer, and I have yet to run into adhesion issues. Therefore; Buy it, keep it clean with 99.9% IPA, and you will not regret it :-)

I had problems getting the PLA material to remain attached to the original textured matte that came with the Ender3 v2 neo. Using a PEI matte made a huge difference. I have not had issues with my projects detaching from the printing matte since I started using it.