Creality Capricorn Bowden Tubing 1M, Bowden PTFE Tube for 1.75mm Filament with Teflon Tube Cutter, 2X PC4-M6 Extruder Fitting & 2X PC4-M10 Hotend Fitting for Ender 3 V2/3/3 Pro/5/CR-10/10S 3D Printer
-
jay bullin
> 3 dayEvery piece of this kit is better than the Ender 3s factory version. Only issue is the fittings tend to bite into the tubing so incredibly well that they do NOT release when you try to take the tubing out.
-
Not Ron Burgundy
> 3 dayIt does the job
-
Bonita Schuppe
> 3 dayOrdered this after my Ender tube started wearing down and causing feeding issues. My Ender is highly modified, and does not have a typical feed. I wish I had used one of these a long time ago!
-
michael mcknight
> 3 dayVery easy to install and works really good.
-
Rob Terry
> 3 dayAny printer that uses a Bowden tube suffers a bit from the tube itself. These make the friction as low as it can be and tolerate much higher temps. For my FLSUN Super Racer, using these has led to a consistently better experience with the printer with less jams and more consistent printing.
-
Richard Kindred
> 3 daySee the headline, I am not able to use the item at this time.
-
Ron Walters
> 3 dayEasy install and a big improvement from the stock tube. All my printers are now upgraded with this.
-
William A. White
Greater than one weekMy prints came out a lot better when I swapped out the stock bowden tube with this. This is the second set Ive used, the others having been burned up by a clog in the hot end. Theres a trick to installing it. You unscrew the nozzle between a full turn and half a turn, install the tube and tighten up the nozzle again. That jams the nozzle and tube together to keep plastic from leaking out between the gap. You can see this on YouTube videos, but I forgot about it with my last Bowden tube upgrade, and got a bad clog and poor quality prints. I will always buy this for Bowden tubes.
-
otsego
> 3 dayEverything that came in this package is better quality than the stock equipment. I would definitely have a few of these around if your printing often
-
PM
Greater than one weekPerfect fit
Compatible Models: Ender-3 S1/Ender-3 S1 PRO/Ender-3 S1 Plus/Ender-3 NEO/Ender-3 V2 Neo/Ender-3 Max Neo/Ender-3/Ender-3 Pro/Ender-3S/Ender-3 V2/Ender-3 Max/Ender-5 Pro/Ender-5 Plus/Ender-6/Ender-7/CR-10S Pro V2/CR-10 V3/CR-10 V2/CR-10 Max/CR-6 SE/CR-6 Max/CP-01 / CR-30/CR-X Pro
1 Meter Creality Original Capricorn Bowden PTFE Tubing
Capricorn Premium XS Bowden tubing, with an extremely precise inner diameter tube design, was developed specifically for 1.75 mm filaments, making it easier for you to print with flexible filaments. It is reinforced with a proprietary high-performance additive blend and is recognized as the highest quality PTFE tube available for all 3D printing. Tight tolerances ensure that the filament leads directly to the hot end, with the smallest possible margin of error between the extruder and the hot end, which is critical to the success of printing flexible filaments.
Packing List
- 1 x 1M Capricorn Premium XS bowden Tubing
- 2 x PC4-M10 Pneumatic Fittings
- 2 x PC4-M6 Pneumatic Fittings
- 1 x Tubing Cutter
|
|
|
|
|---|---|---|
Imported Teflon Tube,Constant Inner DiameterMade of Teflon resin imported from Japan, the smoothest substance known to man, extremely smooth inner wall, high precision inner diameter, faster and better extrusion efficiency. More flexible, heat resistant, moisture resistant, non-stick surface, wear resistant and corrosion resistant. |
Robust and Durable CouplersPC4-M6 coupling: made of high quality copper and plastic, sturdy and durable. Thread M6/3mm, inner diameter 4mm, suitable for tubes with outer diameter 4mm. PC4-M10 coupling: made of high quality stainless steel and plastic, high hardness, anti-oxidation and anti-corrosion. Thread M10/6mm, inner diameter 4mm, for tubes with 4mm outer diameter. |
Include PTFE Tube Cutter, No More HeadachesThe PTFE tube cutter is equipped with a sharp blade that easily cuts the sides of PTFE tubes flat, preventing any failure or thermal creep during feeding and retraction. With the pipe cutter, no more headaches with uneven cuts, saving time and material! |
|
|
|
|
|
|
|
|---|---|---|---|---|---|---|
| CR Touch Kit | PEI Build Plate | Ender 3 Magnetic Bed | Ender 3 Glass Bed | 1M Capricorn Bowden Tubing | LED Light Bar | |
| Fit For | Ender-3, Ender-3 Pro, Ender 3 Max, Ender-3 V2, Ender-5, Ender-5 Pro, CR-10 3D printers with 32 Bit V4.2.2/V4.2.7 Mainboard | Ender 3, Ender 3 Neo, Ender 3S, Ender 3 Pro, Ender 3 V2, Ender 3 V2 Neo, Ender 5, Ender 5 Pro | Ender-3, Ender-3 Pro, Ender-3S, Ender-3X, Ender-3 V2, Ender-5, Ender-5 Pro, CR-20, CR-20 Pro,Voxelab Aquila, Geeetech A10 series, Artillery Genius, BIQU-B1 | Ender-3, Ender-3 Pro, Ender-3S, Ender-3X, Ender-3 V2, Ender-5, Ender-5 Pro, CR-20, CR-20 Pro,Voxelab Aquila, Geeetech A10 series, Artillery Genius, BIQU-B1 | Ender-3, Ender-3 Pro, Ender-3 V2, Ender-5, Ender-5 Pro,CR-10, CR-10S, CR-20, CR-20 Pro and Other Similar 3D Printers | Ender 3, Ender 3 V2, Ender 3 Pro, Ender 3 V2 Neo, Ender 3 Neo |
| Type | Auto Bed Leveling Kit | PEI Build Plate | Print Bed | Print Bed | Bowden Tube | LED Light Bar |