Official Creality PEI Sheet 235x235mm Flexible Removable Spring Steel Plate Magnetic Sticker Heated Bed Kit Replacement Accessory for Ender 3 S1/Ender 3/Ender 3 V2/Ender 3 Pro/Ender 5 Hot Bed Surface
-
Jon Nolen
> 3 dayThis and BLTouch are must have upgrades to any ender 3 setup. ABS prints wouldnt stick to glass or the buildtak magnetic bed without ABS juice... this *just works*. print removal is super easy, just flex the bed a bit.
-
Joshua B.
> 3 dayWorks great, much better than glass, and easy to install
-
JS
> 3 dayThis is the second (one for my other printer) of these that I purchased. My preferred print surface. Makes removing prints easy.
-
Chris
> 3 dayIts flexy, its springy, its magnetic too. The PEI is great, super adhesive, but not so much that its impossible to remove when the print is done. I like it, you will too.
-
kendall
> 3 dayBought in June in July the top layer has began bubbling up. Worked great up until then. Definitely wouldn’t spend the premium price for this bed surface again.
-
Z N
> 3 dayThis had to be a return. The corner was dented in as if dropped, had scratch drags from a printing head scrapping and the beginnings of a layer coating coming off. Not sure if it would work as intended.
-
Eddison
> 3 dayClean prints great adhesion. Love the pop. I rarely have to use a tool but on super small prints I found plastic razor blades upside down are amazing and do not damage the PEI
-
Brad Fisher
> 3 dayThis has been a game changer for me. I fought with too much adhesion to a PEI glass sheet. I would commonly break prints trying to remove them. Just lift the front of this and everything pops off of this. No complaints whatsoever. I have not had any issues with prints staying adhered yet either.
-
Salado
Greater than one weeka great upgrade for my Ender 3 S1, super smooth surface with good adhesion. 5 stars
-
Rachel
Greater than one weekI switched to this type of bed plate/removable sheet after having issues with both the textured ones and printers original glass bed. This one bends just enough to easily pop off your prints without needing to pull hard, if at all. After 3-5 prints I wipe down with some rubbing alcohol or windex to get any finger oils off the surface. The more buildup, the more issues youll have with your print adhesion. When its clean and I set it to the right temp for my PLA, I have no issues and it sticks great! Highly recommended. No more spatulas!
100% Official Creality PEI Removable Magnetic Flexible Heated Bed Platform is mainly divided into 3 layers:
- The first layer is made of PEI material. Smooth surface, good adhesion to various printing materials, especially PLA and ABS, high-temperature resistance.
- The second layer is a flexible steel plate, which is specially used to make springs and flexible elements, has strong deformability.
- The third layer is the magnetic base，which is made of soft magnetic rubber, soft in texture and has good magnetism and temperate, bure resistance. With 3M adhesive, it can be directly attached to the heated bed platform.
NOTE！
- 1.Please remove the transparent protective film on the surface before use!
- 2.Level the bed and set the height of the nozzle before printing!
- 3.Please use the recommended/usual nozzle and hotbed temperature for printing. If it cannot adhere, please try to change 2 or 3 degrees.
- 4.The PEI sheet can bear the maximum temperature of the nozzle at 200°C, and the hotbed at 70°C.
- 5.The color may exist a slight difference due to different screen displays.
|
|
|
|
|---|---|---|
Strong magnetic fieldUsing 3M adhesive to attach the soft magnetic sticker to the hotbed will no damage to the magnetic field under 130°C. |
No deformation at 200°CGenuine PEI powder coating is of heat resistance. Hardened steel spring plated is resistant to 200°C and no deformation. |
Handle designThe new design adds a handle to the steel plate, which makes it easier and faster to take out the steel plate. And outside the heated bed, it will not burn your hands. |
|
|
|
|
|---|---|---|
Quickly RemoveNo need for tape, glue, and shovel which release your printing anxiety. Easy to remove the prints just take out the spring steel plate and slightly flex it repeatedly to pop your prints right off. |
Smooth BottomThe PEI printing plate surface is smooth that will not leave any marks on the bottom of the prints. There is a good combination of hot-melt material and the printing layer, which reduces the deformation caused by shrinkage and avoids warping. |
Easy to cleanPlease clean the dust with a soft cloth. Wipe the stains with Low concentration alcohol gently. Do NOT wash or clean the PEI surface with any strong chemical reagents, or strong detergents. |
