













Thermalright Intel 12th/13th Generation LGA1700 Anti-Bending Buckle,CPU Stress Bending Correction Fixer, Curved Pressure Plate,Fully Fitted and Fixed Without Trace Installation (Black)
-
Aurelio M
Greater than one weekWhen I bought my i7-13700K, the CPU would randomly spike to 100 °C while idle and stay at that temperature for 4 to 5 minutes. I upgraded my CPU cooler to a corsair 420 mm CPU watercooler, but the same issue occurred, although it didnt stay as long at 100 °C. The problem disappeared when I switched to the Thermalright contact frame. I also noticed an improvement in the average temperature of the CPU at idle and under load. It is clear that this contact frame helps the CPU behave in a better way, especially for a CPU that is known to overheat.
-
ryan
> 3 dayCombined this plate with a very slight undervolt on my 13700k and now its maxes out around 85C as opposed to thermal throttling before. 100% these plates are essential for keeping new Intel cpu temps under control.
-
Kevin L. Greer
> 3 dayThis thing is so simple to install . Not expensive, but works like a charm.
-
Eric Ward
Greater than one weekInstalled this on my Asus Maximus Z790 Hero with no problems. Used factory screws from motherboard and no issues. Make sure to tighten in criss cross pattern to make sure it tightens evenly and doesn’t bend. Highly recommend as this also lowered my CPU temps on my 13900k
-
audiom3
> 3 dayThis is my first build in 4.5 years, so this time around I wanted to do tons of research. Im installing a CPU water cooler for the first time ever and researching that a fair amount led me to these CPU brackets. Ive never been satisfied with the cheezy, light weight CPU brackets/fasteners which come standad on MBs. This seemed like a valuable asset for just $14. Im running a 13th Gen Intel on an MSI Z690 ACE MB. As you can see from the pic, the fit looks very clean and the aluminum bracket is well machined. I do not know if temps will be lowered vs the stock guillotine bracket but it sure holds the Intel in place far better. And that can only be good.
-
Eric
> 3 daydecided to rebuild my computer using a i7-12700k and from what i read and what all my builder friends told me, having this retainer is a must for the long term, as it helps mitigate temperature spikes and evens out the CPU to Cooler contact, allowing for an even heat distribution. Now, I’m not super computer savvy and I’ve only built 3 computers in my lifetime, but if I can install this easily, than anyone can.
-
surferboy2177
> 3 dayI was a little nervous about installing this at first, but it was surprisingly easy. I placed it on my 17-13700K CPU and I noticed my temps went from Mid 40s to high 30s while in windows, and when running Cinebench I went from low 90s to mid to low 80s. Overall highly recommend if youre comfortable with taking apart your computer. Takes less than 10 minutes.
-
Todash Man
> 3 dayWorks. Got my temps down a little bit.
-
73
> 3 dayIf you have a 12th or 13th gen processor, this is a must have. I installed this frame on two different computers and it dropped temps by at least 8 degrees on each. Install is super easy if you follow the steps in the Gamers Nexus youtube video.
-
Constantine
> 3 dayLook I realize Thermal Grizzly basically thought of these as a solution for the 1700 socket bend but they’re super expensive and hard to find in the States. And yes, there are even some builders that believe these contact frames are just a trend and are nothing more than a security blanket for a nonissue. And in same cases that’s absolutely true. Some CPUs IHS are perfectly fine with the socket bend I had 4 that were completely fine with or without the contact frame. But after 15 builds with extreme socket bend making for poor contact with heatsinks I can say this helps more often than not. This contact frame has lowered temps by upwards of 8C on my builds and yes I tested each one. So yes, in my professional opinion Intel created a problem, never addressed it and these are the best solution, especially for anything Core i7 and up. The fact that Thermal Right created these at such a reasonable price and are indeed just as effective as Thermal Grizzly’s (check Gamers Nexus) seems too good to be true, but as I’ve said I’ve used these on 15 builds and they’re worth every penny.