Rocaris 10 Pack Flap Wheel, 120 Grit for Rotary Tools，1/8 inch Shank (32X10X3)

DESCRIPTION: This is a set of ten abrasive flap wheels, intended for use in hand-held motor tools such as a Dremel brand. The dimensions are 32mm (overall diameter) x 10mm (width of individual flaps) x 3mm (shaft diameter). --------------- POTENTIAL USAGE: I used this product as intended, in a hand-held Dremel tool. It worked as expected on wood and metal surfaces. As with any powered abrasive tool, it sheds a lot of specks of abrasive, so proper personal protection is essential for safety. I generally work under a plastic shield, but I removed the shield for the staged photo. The 1/8 (3mm) shaft also fits in a stationary drill press for constant medium-speed use. This worked well for smoothing edges of wood pieces. The shaft also fits in a portable cordless screwdriver for slow or variable-speed use, and would work well for irregular surfaces such as automotive panels, deburring pipes, or in locations without AC power. Since these tools are reversible, it is important to be sure the flap wheel is turning in the correct direction (as if you were tightening a screw). --------------- MY USAGE: I primarily use these for polishing and brightening the wheels of model train locomotives. These wheels must be kept spotless as they provide the electrical connection to the locomotive. While holding the locomotive in a cradle (see photo) I could easily address the wheel surfaces using a light touch. I had previously used a little wire brush wheel for this purpose, but that was a bit too aggressive for this use. --------------- Note the online listing for this product specifies 120 grit in the description, but 80 grit in the illustration; so not sure which is correct.

These were just the right size to use on my water pump. I wanted to clean inside the ports. I am used to flap wheels will a larger shank (1/4) but these smaller 1/8 shank worked fine. Will need to get some with a coarser grit for other projects. Would buy these again. Thumbs up.

Flap wheels are a staple in any rotary tool/flex shaft accessory kit; they offer an easy way to carve, smooth, and blend curved areas of a surface. The Rocaris 10-pack, at about $1 per wheel, is about one-half to one-third the price of my favorite name-brand flap wheels. As you might expect, theyre not quite as well put together as the more expensive versions: The glue joints can be a little uneven, the trim on the flaps can be kind of haphazard...but given the abuse these wheels get, its probably a minor issue. From what Ive seen in my first wheel, theyre not going to last as long as some, but again, at the price thats a minor issue. Less minor: They are positioned as 120-grit AlOx wheels, but as others have noted they seem more aggressive than that. The initial cutting is more like an 80-grit at least. However, after a couple hours use, they soften up to about where I expected them to be, out of the box. (Hint: If youre buying inexpensive abrasives, its ALWAYS a good idea to test them on a piece of scrap (metal, wood, glass, stone), and compare them to what youre used to.)

These a very durable flap wheels, they are very securely glued, I suspect I could sand right down to the knub and never lose a flap. I will say the 120 grit is a very abrasive for most wood detail work and the flaps do not yield much, adding to the extra abrasive qualities of these wheels. These would probably sever better for metal detail work/projects. I wish they listed the grit size on the product, I think it might be on the back of the flaps somewhere, but the writing is so big and the flap is so small, youd never be able to read it. They should print it right on the end, or on the little sticker that lists the wheel size. Overall, a useful product, just know the 120 is very abrasive for wood detail work.

Flap wheels are a staple in any rotary tool/flex shaft accessory kit; they offer an easy way to carve, smooth, and blend curved areas of a surface. The Rocaris 10-pack, at about $1 per wheel, is about one-half to one-third the price of my favorite name-brand flap wheels. As you might expect, theyre not quite as well put together as the more expensive versions: The glue joints can be a little uneven, the trim on the flaps can be kind of haphazard...but given the abuse these wheels get, its probably a minor issue. From what Ive seen in my first wheel, theyre not going to last as long as some, but again, at the price thats a minor issue. Less minor: They are positioned as 120-grit AlOx wheels, but as others have noted they seem more aggressive than that. The initial cutting is more like an 80-grit at least. However, after a couple hours use, they soften up to about where I expected them to be, out of the box. (Hint: If youre buying inexpensive abrasives, its ALWAYS a good idea to test them on a piece of scrap (metal, wood, glass, stone), and compare them to what youre used to.)

Currently working on refinishing some metal baseboard radiators that were looking tired and rusty. I used these in my Dremel to get at areas a palm sander couldnt get to as well as to focus in on particularly rusty spots as well as decades old paint blobs. Definitely sped up the process and reduced the pre-sanding time as I prepared the parts for new paint. Exactly what I was expecting.

These are good and worked great in my Dremel for sanding on tight corners on wood when prepping for refinishing furniture. Smooth nice finish once removing current coatings and finish

Does what it needs to do. Perfect for the do it yourselfer. Great for woodworking and other forms of hobby sanding.

Flap wheels are a staple in any rotary tool/flex shaft accessory kit; they offer an easy way to carve, smooth, and blend curved areas of a surface. The Rocaris 10-pack, at about $1 per wheel, is about one-half to one-third the price of my favorite name-brand flap wheels. As you might expect, theyre not quite as well put together as the more expensive versions: The glue joints can be a little uneven, the trim on the flaps can be kind of haphazard...but given the abuse these wheels get, its probably a minor issue. From what Ive seen in my first wheel, theyre not going to last as long as some, but again, at the price thats a minor issue. Less minor: They are positioned as 120-grit AlOx wheels, but as others have noted they seem more aggressive than that. The initial cutting is more like an 80-grit at least. However, after a couple hours use, they soften up to about where I expected them to be, out of the box. (Hint: If youre buying inexpensive abrasives, its ALWAYS a good idea to test them on a piece of scrap (metal, wood, glass, stone), and compare them to what youre used to.)

Working on a project with live edges and needed flap type disks. Fits perfectly in my rotary tool and allowed me to sand down the live edge without losing its natural beauty. A flat sanding disk wouldn’t have been able to handle the contour surfaces without removing excessive material. Overall excellent product and great addition to my rotary tool set.