Seven Sparta Hood Latches Aluminum Hood Catch Compatible with Jeep Wrangler JK/JKU 2007-2017, JL/JLU 2018-2022 & Jeep Gladiator 2020-2022, 1 Pair (American Flag)

Very nice product. Much needed upgrade from the original latch. The lower section of this latch is difficult to install due to the location of the nut that you have to get to. Your need a socket extension to get to it.

Not difficult for me to install, but I do have a full garage of tools. If youre tool limited it could present a challenge getting to the lower hinge.

Easy install for the average Jeep owner. 15-20 minutes max. Right and secure for after adjustments. Excited to not see any hood flutter next time on the turnpike.

Purchased these awesome Sparta Latches a few weeks ago and it was a breeze to install, best part was the double bolt fit I only found available from this seller and conveniently on Prime--- Same Day Delivery! I was in a bind to get these latches repaired as I am in process of selling my 2011 Jeep 2D Wrangler ! I was Driving down a 2 Lane highway one day and passed a 18 wheeler about 65 mph, the gust literally blew the stock latch right off, it was 10 years old definitely a little worn out. Sounded like a gunshot through the window and scared the living daylight out of me, so thankful these replacements worked out. I am a 35 year old woman with a socket wrench kit I got at 18 years old, I was able to figure this out and fit my hands behind the grill and corner fender which helped to arrange unassembled the lower original bolts and washer and put on the new ones. Note you have to take apart the actual new bottom clip to tighten on but its a simple instruction and video helped on the page ! Good luck, I love the look of these should have purchased sooner!

These latches are well made and look great. And the hood doesnt pop every time a Peterbilt passes on a 2 lane highway. The only thing I would advise a Jeep owner is these do not give, they are solid. If you are an avid off-road enthusiasts I would think about the fact these latches have no elasticity to allow flexing in extreme condition.

This does include a very colorful poster style instruction sheet that has extremely vague instructions. For example, the first instruction is: 1. Factory hood latch is made of plastic remove the factory hood latch. And there is a picture of the hood latch locked in place on a closed hood. It neglects to tell you you have to remove the front grill. And you have to navigate a socket wrench from below the headlamp to squeeze it in between the body panel and engine compartment. Tip that i hope will save someone some time and aggravation: the factory nut is a 1/2 inch and comes off pretty easy once you navigate the socket wrench past the headlamps. But my biggest issue is the hex head screws are extremely weak metal. I had not notice the JK specific gaskets and initially installed using the pre-fitted JL gaskets. I was able to remove one mount but the second mount screw stripped the hex. Of course it is too low clearance to reach in behind so Im stick with a 70% tighten screw that wont come out nor go back in. Wasnt using anything more that a standard socket wrench and the included hex key and yet the screw rounded out. After over an hour trying various method to remove the screw I eventually gave up and just dealt with the passenger side lower mount being slightly loose. I may someday use the screw extractor to get it out but for now it works fine and the JL gasket works well enough. All that being said the mounts are good construction (except the weak screw head mentioned above). The hood latches tightly and no move windblown hood bounces at +55mph. Looks sharp too, just mildly irritating that I cant affix the a proper gasket and tighten it up.

Better than factory latches.

Wouldn’t buy again. They look nice and are Strong but kinda hard to line up

Heavy duty. Quality product

These good latches look great on my red 2008 JK Rubicon. Not only are they nice looking but they also did away with the hood shutter that I was getting from the wind.