TORACK 3Pcs Metal Pegboard Panels for Wall Garage Utility Tools Pegboard Storage System for Workbench, Shop, Shed Modular Peg Board Organizer Board Kit(Pack of 3, Grey)

This kit comes with three metal pegboard panels and mounting hardware. Each pegboard has a black painted finish that is scratch resistant and durable. The pegboards are available in black or white. The heavy duty metal will hold up to years of use, abuse and heavy loading. The pegboard hole pattern will fit any 1/4 and 1/8 hangers (not included). I mounted these on the wall next to my basement workbench and had no problem loading them up with tools. In fact, Ill likely get more pegboards to help organize the rest of my tools. Would recommend this to anyone.

In the interest of full disclosure, as a trusted and unbiased Amazon reviewer, I was able to request this product free of charge. Nicely made racks, heavy weight and durable. Clean finish. There is a rolled edge on the top and bottom. There are no welds in any of the corners that I can see; however, this doesnt matter as these are plenty strong. These do not accept 1/4 inch hooks. I have some hooks that measure 3/16 of an inch and although these will insert into the holes, they will not make the bend in order to be used. These racks work fine with 1/8 inch hooks only. When mounted, the distance from the wall is approximately 11/16 of an inch - more than adequate spacing to insert your hooks. A nice product just wish they accepted 3/16 - 1/4 inch hooks.

These are far superior to the wood pressboard type. I love that no spacers were needed. They just screw directly to your wall and at spaced perfectly due to the offset. They have a very clean look. Moisture won’t deteriorate or make them swell like traditional pegboard. The sizes are perfect for mounting horizontally or vertically so they are really adaptable to your space. Perfect for garages, laundry or hobby areas.

I have to say I love that they came with the screws AND the anchors, but the holes in the pegboard were too small to insert a pencil into for marking the wall for the drill points. I had to use the pointy end of a long skinny awl to mark the wall. Also I had to employ a bit of trial and error because the diagrams/packaging did not indicate the sizes of drill bits needed for installation. It also mentions you need a hammer but never mentions the hammer being used in any of the text directions. I took measurements (and notes) as I installed the first board to make installing the other two pegboards easier. Ill share those measurements here. For inserting the anchors into the wall I used a 5/16 drill bit. The top far left hole is 11 away from the far right top hole. The top left hole is 22 7/8 from the bottom left hole (and of course the same distance goes for the holes on the far right side. If one or more holes are over a stud, you wont need the anchor. For that hole you would use the 3/16 drill bit. As you can see in my photo, I did not install them immediately next to each other but instead chose to install each of the three in between the tracks for my track mounted shelving system in my sewing room. Now I can use my existing shelf brackets and shelves until I get more pegboard accessories. Definitely recommend them. I can use magnetic hooks, pegboard hooks, etc. I have been wanting pegboard but much preferred the idea of having it be metal.

These three pegboard panels are made of a sturdy metal and come with mounting hardware and instructions (not that instructions for this are really needed). The finish is good and there are no sharp edges or burrs anywhere on them. As you can see in the pictures, I have not installed them yet but that will be completed over the wekend. The pegboard hooks fit perfectly and if the panels are installed properly, these will reliably hold a lot of weight. Anyone that has used those thin cardboard like (particle board?) pegboard panels will love how much better these metal panels are. Some may think these are a little pricey but I would disagree. These will last longer than I will. Worth every penny.

The panels arrived in a well-protected box, and we were pleased to see that none of them were scratched, dented, or scraped. Installation was a breeze, and they paired effortlessly with the peg bins, hooks, and shelves that my wife had purchased earlier. The panels are remarkably sturdy, and we have had no issues with them warping or cracking. However, one shelf did break when my wife overloaded it with plastic hooks, but the metal pegboard itself remained unscathed. We found these to be excellent for the craft room, and I am even considering purchasing some for my garage after witnessing their usefulness.

Very rigid

I look forward to being able to hang these in the garage and better organize my tools in a visible space. While maybe not the size of a full pegboard sheet, Id still trust these over the fiberboard to hold heavier tools. Just make sure you hit studs and youll be golden. The finish is nice, I tried to scratch it with a key and couldnt make more than a barely visible mark on it. Now I just have to order the pegs!

These metal peg boards are well-made and heavy. The size of the panels gives the user a lot of versatility in configuring them.

Super easy to install and even comes with screws to attach to the wall. Super sturdy metal!