ANYCUBIC 3D Printer Resin with Low Odor and Safety, 405nm UV Plant-Based Rapid Resin with High Precision and Quick Curing for LCD 3D Printing (Grey, 1000g)

(960 Reviews)

Price
$19.99

Color
Quantity
(60000 available )

Total Price
Share
138 Ratings
84
14
13
4
23
Reviews
  • Joe C

    > 24 hour

    A lil expensive but worth it

  • Faboo

    > 24 hour

    I tried this resin for the first time yesterday on an Anycubic Photon printer and had very good results. First, as advertised, it doesnt smell bad. This makes it easy to be around and work with i.e. not wearing a full respirator, which is a huge improvement over other products. Print quality good: Resolution was great, limited by the printer resolution, not the resin. The resin is a nice low viscosity, poured easily and didnt hold bubbles under the surface. Exposure time as advertised: I used values in the middle of the range of suggested exposure times from the instructions and had no problems with curing or adhesion to the build plate. Tank adhesion better: During printing, I believe there was less adhesion to the FEP tank liner than with standard resin, as the slight popping sound as each layer detached was quieter. - see note on supports next. Post processing is different: After removal from the build plate, I rinsed with an alcohol bath. The surface of the print was still a bit tacky after rinsing. (this is corrected with time in the sun or a post-cure light setup) I removed the supports and found that the material in its green state was less brittle and a little stronger than the anycubic standard resins. This means that it is a little harder to remove supports, so I would recommend using a lighter support structure to avoid damage to the print where the supports detach- this seems reasonable given the lower adhesion to the FEP tank window that I think I observed. Finishing good: I post-cured the print in front of a 30W 405nm UV light for 4 hours. The material cured with a matte finish. I tried filing and sanding the support scars and had good luck with both methods. After sanding with a very fine paper, I rubbed the print with a cotton cloth and was able to match the appearance of the undisturbed surface fairly well. Strength: I did not test the ultimate strength or brittleness of the fully cured material, but will update when I do.

  • Ian Chess

    > 24 hour

    Great details, almost no odor, Ill definitely be buying more of this!!!

  • Sarah

    > 24 hour

    Ive tried everything I know, followed directions, played with settings. No matter what I do 30% or more of my base layer and supports just dont stick to the build plate at all. Ive tried several prints of varying difficulty a d each has come out malformed or warped if it manages to print at all. I wont be ordering g this again. For those wondering I have a Mars 3.

  • Kirk R.

    > 24 hour

    Very nice prints once the resin settings are tweaked or your printer. Recommended.

  • Jon

    > 24 hour

    Ive ordered this 2 times now, and on my last shipment I received clear instead of black, I said screw it and tried it, and the clear is really nice too. Just wish I had gotten the black I ordered. UPDATE !! anycubic contacted me, and then credited my account because of a picking error. GREAT CUSTOMER SERVICE . Ill continue to use anycubics eco resin for sure. Thank you Jane !

  • Melissa Palzewicz

    > 24 hour

    Thought Id try out Anycubics low odor resin. I was surprised by how little odor there was. I printed some hummingbird earrings, and they turned out great!

  • Mr. Reilly Walsh IV

    > 24 hour

    I didnt think it was that big of a difference in smells. But worked like it should have!

  • Stephen Feather

    > 24 hour

    Normally I buy a bit more expensive and use-specific resins (heat, flexibility, strength) Hadn’t tried this new “low oder” resin yet so threw it into a cart. “Low” is pretty subjective. For me, it is not as obnoxious as many of the other resins. I still wear a respirator when the machines cover is off and when cleaning up machine and tools. Headaches, watery eyes, etc still occur. Using IPA 90+ for washing, nearly all the residue is removed. Prints left on the plate over night have come out fine. Resin left in vat for 48 hours still binds well. Halot One Plus settings: Bottom time: 25s Bottom layers: 6 (I have some very thin models that warp right off the plate if not set strong early, adjust as needed) Exposure time: 2.5s (3s if you are new or if you have a lot of hours on your lcd) Lift speed: 2mm/s Light delay: 1s Lift height: 6 (5 works with a filled vat, 6 is safer if running towards running the vat out to ensure the resin flows back in time)

  • Keith T

    > 24 hour

    I am not using this in a printer, but I am using it to smooth out FDM prints and get rid of layer lines as part of post processing. It being clear allows the resin to quickly and completely cure. A thin layer brushed on is all that you need. After a quick primer coat you are ready to paint the model. Huge time saver for post processing!!!

plant based resinplant based resin
plant  based resinplant  based resin

Ultra-Low Odor

Soy extract formula, BPA-free, benzene toxin-free and irritating VOCs volatile-free.

plant based resinplant based resin

Good Fluidity, Fast Printing

ANYCUBIC 3D Plant Based Resin with good fluidity means it has low viscosity during the printing process and helps to improve printing speed.

plant based resinplant based resin

Low Shrinkage

Print with fast curing speed and low shrinkage rate provide the excellent printing experience and effects.

plant based resinplant based resin

Stunning Colors

High precision and quick curing for LCD 3d printing and high quality pigments provide stunning colors in our range of resins and available colors.

plant basedplant based
wide applicationwide application
3d resin3d resin

ANYCUBIC 3D PRINTER RESIN FAMILY

resin

Plant-Based Resin

ANYCUBIC 405MM UV RESIN

Standard Resin

Water-Wash Resin +

Water-Wash Resin +

resin

ABS-Like Resin +

resin

Tough Resin

ANYCUBIC DLP CRAFTSMAN RESIN

DLP Craftsman Resin

ABS-Like Pro

ABS-Like Pro Resin

Features Ⅰ
Soybean Oil Formula Ideal for Beginners Easy to Clean Up High Strength Ideal for the Professional More Exquisite and Smooth Industrial Grade Performance
Features Ⅱ
Low Odor Easy to Shape No Need Extra Alcohol Excellent Toughness High Impact Resistance Lighter Lamination High Strength and Toughness
Compatibility
LCD/DLP LCD/DLP LCD/DLP LCD/DLP LCD/DLP LCD/DLP LCD/DLP
Wavelength
365-405nm 365-405nm 365-405nm 365-405nm 365-405nm 365-405nm 365-405nm
Viscosity
250-300mPa·s 250-300mPa·s 200-300mPa·s 200-300mPa·s 150-250mPa·s 200-300mPa·s 400-500mPa·s
Density
1.12-1.20g/cm³ 1.13g/cm³ 1.15-1.20g/cm³ 1.05-1.25g/cm³ 1.10-1.15g/cm³ 1.15-1.20g/cm³ 1.12-1.20g/cm³
Surface Hardness
82-85D 82-85D 80-85D 82-88D 74-78D 80-83D 85-88D
Tensile Strength
35-45MPa 36-50MPa 40-50MPa 37-50MPa 25-40MPa 32-43MPa 50-65MPa
Elongation at Break
8-15% 7-14% 8-18% 15-20% 35-50% 11-14% 20-30%
Flexural Strength
40-50MPa 45-70MPa 45-60MPa 38-50MPa 40-50MPa 50-60MPa 60-70MPa
Molding Shrinkage
3.8-4.5% 4.5-5.5% 4.2-5.5% 4.3-5.6% 5.1-6.2% 4.2-5.5% 3.4-4.0%
Shelf Life
1.5years 1.5years 1.5years 1.5years 1.5years 1.5years 2years

Related products

Shop
( 2666 Reviews )
Top Selling Products