Rocaris 10 Pack Flap Wheel, 120 Grit for Rotary Tools，1/8 inch Shank (32X10X3)

These are good and worked great in my Dremel for sanding on tight corners on wood when prepping for refinishing furniture. Smooth nice finish once removing current coatings and finish

these are just what they say they are and they do exactly what they are supposed to do. what more is there to say?

I use these to knock rust off automotive parts. These will fit the bill.

Does what it needs to do. Perfect for the do it yourselfer. Great for woodworking and other forms of hobby sanding.

DESCRIPTION: This is a set of ten abrasive flap wheels, intended for use in hand-held motor tools such as a Dremel brand. The dimensions are 32mm (overall diameter) x 10mm (width of individual flaps) x 3mm (shaft diameter). --------------- POTENTIAL USAGE: I used this product as intended, in a hand-held Dremel tool. It worked as expected on wood and metal surfaces. As with any powered abrasive tool, it sheds a lot of specks of abrasive, so proper personal protection is essential for safety. I generally work under a plastic shield, but I removed the shield for the staged photo. The 1/8 (3mm) shaft also fits in a stationary drill press for constant medium-speed use. This worked well for smoothing edges of wood pieces. The shaft also fits in a portable cordless screwdriver for slow or variable-speed use, and would work well for irregular surfaces such as automotive panels, deburring pipes, or in locations without AC power. Since these tools are reversible, it is important to be sure the flap wheel is turning in the correct direction (as if you were tightening a screw). --------------- MY USAGE: I primarily use these for polishing and brightening the wheels of model train locomotives. These wheels must be kept spotless as they provide the electrical connection to the locomotive. While holding the locomotive in a cradle (see photo) I could easily address the wheel surfaces using a light touch. I had previously used a little wire brush wheel for this purpose, but that was a bit too aggressive for this use. --------------- Note the online listing for this product specifies 120 grit in the description, but 80 grit in the illustration; so not sure which is correct.

Flap wheels are a staple in any rotary tool/flex shaft accessory kit; they offer an easy way to carve, smooth, and blend curved areas of a surface. The Rocaris 10-pack, at about $1 per wheel, is about one-half to one-third the price of my favorite name-brand flap wheels. As you might expect, theyre not quite as well put together as the more expensive versions: The glue joints can be a little uneven, the trim on the flaps can be kind of haphazard...but given the abuse these wheels get, its probably a minor issue. From what Ive seen in my first wheel, theyre not going to last as long as some, but again, at the price thats a minor issue. Less minor: They are positioned as 120-grit AlOx wheels, but as others have noted they seem more aggressive than that. The initial cutting is more like an 80-grit at least. However, after a couple hours use, they soften up to about where I expected them to be, out of the box. (Hint: If youre buying inexpensive abrasives, its ALWAYS a good idea to test them on a piece of scrap (metal, wood, glass, stone), and compare them to what youre used to.)

Working on a project with live edges and needed flap type disks. Fits perfectly in my rotary tool and allowed me to sand down the live edge without losing its natural beauty. A flat sanding disk wouldn’t have been able to handle the contour surfaces without removing excessive material. Overall excellent product and great addition to my rotary tool set.

The 1/8 handles on the 10pk I got were only 1-1/16 to 1-1/8 in length rather than 1-1/4 if that matters. The heads were 3/8 thick and 1-3/16 in diameter though. They fit on my rotary tools just fine. They were similar quality to flap wheels I have had in the past. They come fairly hard, so do note in the product description under tips where they recommend soaking before use. The bottom of the flap wheels is labeled with the rotational speed but is not labeled as 120 grit so I would label them with a marker before use or storing so you will know for future reference. 120 grit is pretty aggressive, so it would be good to do more final shaping on little intarsia wood pieces as well as working on cleaning up rust off metal pieces and such.

Working on a project with live edges and needed flap type disks. Fits perfectly in my rotary tool and allowed me to sand down the live edge without losing its natural beauty. A flat sanding disk wouldn’t have been able to handle the contour surfaces without removing excessive material. Overall excellent product and great addition to my rotary tool set.

These were just the right size to use on my water pump. I wanted to clean inside the ports. I am used to flap wheels will a larger shank (1/4) but these smaller 1/8 shank worked fine. Will need to get some with a coarser grit for other projects. Would buy these again. Thumbs up.