Eastern Jungle Gym Easy 1-2-3 A-Frame 2 Brackets for Swing Set with All Mounting Hardware, Green

This is a sturdy bracket for a swing set or porch swing. However, pressure treated wood will require fitting. I purchased my lumber, 4x6 beam and 4x4 posts from Lowes, so nothing non-standard. I went with pressure treated since the swing will be out in the weather. The beam and post ends required some significant work with a belt sander and coarse grit belts to fit into the brackets. Once the fitting is done and the brackets are installed they look good and will definitely get the job done, but be prepared to put some sweat into the job!

Super sturdy and great coating. I definitely recommend bringing them to store when you are purchasing the wood. Wood is not all cut correctly every time so bring the bracket to confirm the wood you select fits into holes

As many other reviewers have noted, these brackets are very tight fitting on a 4”x6” cross beam. I took the brackets with me to a wood yard and I recommend you do the same. The yard I went to had a new bundle of 12’ 4”x6”s. I sorted through about 10 before I found 2 that the brackets would slip over both ends tightly. The other 4”x6”s would have had to be planed down 1/8”-1/4” to get the brackets to fit. The beams from the yard I was purchasing from were ‘Yellow Wood’, so that shows you what variations in dimensions you could get from a random 4”x6” from the supply store. The brackets have all of the hardware needed to affix to posts and cross beams. There were no issues with any 4”x4” posts fitting. Even though I made sure the brackets would slide over the ends of the 4”x6” cross beams, I still had to use a block of wood and hammer to get them to slide all the way on. I drove them all the way flush to the ends of the beam. If you wanted a 3’-4’ overhang, it would be difficult to get the brackets to slide that far without planing down your cross beam. I made a 24’ swing, so I used these brackets on both ends and a middle support bracket to join the 12’ Cross beams. The middle support bracket seemed to be a little larger than these brackets and went on both ends of the cross beams with relative ease. I installed hardware to hang 3 swings on each 12’ Beam. This allowed for 22” from cross beam end to the first swing and 20” center to center for each swing hanger and 20” between each swing. This is very spacious for my girls (10 and 7) and the 20” spacing also allows ample room for adults to swing. You could certainly fit 4 swings on a 12’ Beam if you needed too. With the 4”x4” posts angled out on the end brackets, you could get by with starting your first swing hanger at around 14” from the end of the beam and be fine. I used 12’ 4”x4” posts to allow the girls to swing higher. I also used a 2”x6” brace on each set of 4”x4” posts. I did not trim the ends of the posts where they join the dirt and I have not anchored my swing set. I tested it out by swinging as high as I could and this set does not move at all. I may bury 4 posts on each end of the swing set and screw the ends of the 4”x4”s too just to be safe as the girls get older and wilder. I attempted to stain and waterproof my wood before putting it up, but it was just too green to hold the stain. I’ll come back and do that in a couple of months. I did have the luxury of using a front end loader to hold the cross beam in the air while I stood the 4”x4” posts up and into the brackets. Most slid right in and tight. If they didn’t, I got on ladder and rocked the cross beam while pulling down and they easily slid the rest of the way down on the 4”x4” posts.

When you install your 4x4x8 legs, the inside edges of the 4x4s that touch at the top (as extended inside the bracket) form an isosceles triangle with long side 95 7/8 and short side 74 7/16 (so in that triangle plane, the legs have an angle of approx. 22.8 degrees from the middle of the triangle) The other angle (which extends over the long length of the assembled swing) is approx. 14.5 degrees from vertical. The net result of this is that you make 4 marks on each of the lines that form the corners of your 4x4. The outer corner you leave (the existing corner is the mark). The inner corner, make a mark 2.5 from the bottom. The corner that is inside-long-way/outside-short-way, make a mark 1 from the bottom. The corner that is outside-long-way/inside-short-way, make a mark 1.5 from the bottom. Now join up these 4 points with lines. These lines form a plane, and you can cut the plane with a sawzall with a long blade. The legs will now sit flat on the ground.

It was decently easy to use, even by myself. The kids have been thrilled with their swingset.

We wanted a swing set for our daughter but did not want to pay the ridiculous price for a full ready to assemble kit. This kit was very easy to assemble. The biggest issue is there were no instructions on my box, but it was pretty easy to figure out. It fit 4x4s for the legs and a 4x6 for three beam very well. It is sturdy enough to support the combined weight of two adults and a toddler (in our case close to 600lbs) with no signs of stress at all. I purchased this set over others because the build looked solid (and it is) and they price was right. I am very pleased with this purchase.

great product

These brackets are exactly what I needed to quickly get a swing set together for the visiting grandchildren.

Brackets are great. Hardware seems fairly cheap.

Before I start my review, you should know a few things. First and foremost I did NOT receive this item for free or at a discount. Second, I am a 34 year old woman who has no experience building anything like a swing set before. I hadnt even used a ratchet before now. I am a biochemist eye disease researcher and mother of a 4 year old boy with autism. My son, like many kids with autism loves to swing. And when I say loves that is a major understatement. His birthday is coming up and I wanted to get him a swing set. We just moved into a new house. Our old house had great trees for swings and this house doesnt. However, nice swing sets are SO EXPENSIVE to buy, so I started looking into the possibility of building one. While I dont have much experience doing anything like this, Im all about trying! Thats when I stumbled upon these brackets and decided I could do it. Im glad I saw the kit version instead of just buying two of the brackets themselves. It saved me a lot of time and trouble buying the right hardware as well. This kit comes with everything you need to assemble the A frame except the wood and tools. I ended up making a basic A frame with a 10 top beam and 10 legs (they recommend 8 legs but I wanted to have a larger swing arc). Heres what I needed to complete the project: - This kit (which comes with two brackets and 28 appropriately sized lag bolts and washers) - One 10 foot 4x6 beam (Home Depot) for the top (be sure to get pressure treated lumber so it will last and wont degrade in contact with the ground) - Four 10 foot 4x4 beams (Home Depot) for the legs (can be anywhere from 8 to 12 feet but I recommend going longer, especially if you plan to anchor the legs in concrete or bury them in the ground. I opted not to bury them but just get some screw in ground anchors. - A drill and drill bit smaller than the lag bolts to pre-drill the holes (already had). I dont know what size exactly I used but it was one that came standard with my drill. - 2 swings. I already had this Deluxe Platform Swing by HearthSong that I bought on Amazon last year and my son loves it. I hung it in our tree using the yellow swing ties that you see pictured - also bought on Amazon. I decided to use them since I already had them. I bought the half bucket swing on Amazon for this project from Swing Set Stuff. - Safe-Kidz heavy duty swing anchor kit (again, Amazon) which came with two anchors, two clips, a drill bit and 4 lag bolts and screws. - Two 80 lengths of zinc chain (Home Depot). I guessed at this amount before building the swing set but only ended up needing about 70 for the half bucket. It all depends on what type of swing youre hanging and the age of the children. - Two Quick Links (Home Depot) to connect the chain ends to the swing - Ratchet and appropriate size bit (again, one that came standard with my ratchet that I already had) With all of this stuff I was able to complete this swing ENTIRELY BY MYSELF in just a couple hours time and that includes the shopping and loading/unloading!! The brackets take all the guess work and careful measuring out of the equation for you. Just slide the wood into the bracket, pre-drill the holes for the lag bolts and ratchet them down and your A frame is finished! A note about inserting the beams into the brackets. Other reviewers mentioned tight squeezes and having to sand or lubricate the beams and then beat them in with a rubber mallet to get them to fit. I was prepared with my orbital sander, dish soap and rubber mallet to do whatever it took but none of that was needed! The beams I bought slid right in with no effort whatsoever. It literally could not have been easier. I guess it depends on where you get your wood, but if its TRULY 4x4 and 4x6 they should slide in to these brackets NO PROBLEM without sanding or lubricating. Before I stood it up (I actually did need help with that part) I measured and installed the mounting hardware for the half bucket swing in the top beam. The manufacturers of the hardware suggest measuring at least 15 away from the nearest structural element of the swing set. I went a little further than that. They also recommend spacing the hardware wider than whatever swing they will be holding. For standard swings 16 should be fine. Thats what I did. Once I stood it up I hung and adjusted the platform swing using my ladder and tested it out myself to be sure it was sturdy. Holy cow this thing isnt going ANYWHERE! Even without being anchored to the ground (which I will do anyway) I was able to swing pretty high laying on the platform without the A frame even wiggling a tiny bit under my 130lb weight! When my husband and son got home from their daddy day that afternoon they were both blown away that I had done it myself and my boy was ECSTATIC!! He LOVES his new swing set and I love how easy it was and that it saved me money! So heres the final price tag on the one I built if it helps: Wood - $100 Bracket/hardware kit - $79 Half bucket swing - $40 Chain - $30 Swing mounting hardware - $28 I already had the platform swing and swing ties but they were $130 and $25 respectively That was only $277 out of pocket and a few hours on a Saturday morning for me which is basically amazing. Total cost including the stuff I already had would put it at $432. For a swing set of this height and sturdiness you would be hard pressed to find something cheaper. Also, this would be very easy to add on to! I intend to add wood planks to the side of the A frame and build a climbing wall on one side and add a slide to the other! Plus Im so proud of myself that I did this. I love sticking it to gender roles! Im telling you, if I could do this, anyone could do this! I have nothing but the highest praise for these brackets and highly recommend them to anyone who thinks swing sets are too expensive or is contemplating building their own! One more free tip for you newbies like me: When working with pressure treated lumber, WEAR GLOVES!!!! Splinters from pressure treated wood are NASTY and will get infected really quickly so save yourself the pain and trouble and just wear gloves from the start. I really hope this helps someone else! Good luck and have fun building!