Smart Dimmer Switch Single Pole, Meross Smart 2.4GHz WiFi Light Switch for Dimmable LED, Compatible with Alexa Google Assistant and SmartThings, Neutral Wire Required, Remote Control Schedule,1 Pack

I put these in my kitchen on six LED can lights and it works great. I also install one in each bedroom for the kids and myself. They are easy to install with instruction right on the app. The switches work really well with Google Home. I can tell Google what level to put the lights to and it instantly does it. You can even program times for the lights to turn on and off. For the kids rooms I programmed the lights to turn off at 10 pm to let them know its time for bed (if by chance they hadnt turned them off by then). I put these and the single-pole switches all throughout the house now I just need to install the three-way switches to finish up all the light.

I wired one of these up to a pair of table lamps sharing an extension cord. I cut the plug end off the extension cord and wired a 3-prong power plug so it could be plugged into a wall outlet. Dont try this unless you have a grasp of electrical wiring. Works great with Google after installing the Mecross app. After plugging it in, it immediately wanted to connect to wifi which was done through the app. It connected in 15 seconds and has stayed connected ever since. Google Home takes over the Mecross app and now controls all on-off and dimming functions. I now have lamps I can control remotely. This is the way these devices should be done in the future....no hubs!

As title states, with all four wires present in the junction box the install is extremely easy. If any of the four are missing (specifically white might sometimes be elsewhere), then the light switch wont function as intended. If you do have all four wires, this switch is extremely easy to use and calibrate. I use mine with Google Home and it functions perfectly! The Meross app also allows you to set up schedules outside of the ones Google Home has.

Ive been a fan of the Meross Homekit switches for a while now. Great affordable option. When you first take a look at them they have wires coming out of the back that would make you think itd fill up the box too much to fit but I had no troubles. Id prefer to have the insert in the back for the wires instead but oh well... once its in, its never an issue again. Im glad to see them coming out with more (affordable) options for Homekit!

I bought this switch to get one step closer to turning my home into a fully functioning smart home and it did not disappoint. This is my 6th Meross product and they make very high quality products that do exactly what you need them to do without complicated things. I installed this on my second floor hallway lights and it was relatively easy although I will say that the traveler wires need to match on both ends but no biggie. I used the Meross app to add the dimmer switch and added it to Apple Homekit without any issues. Another reason to get the switch is the fact that has physical buttons so if there’s ever a wifi outage I can always use the switch normally. This is a a 5 star product all the way although if I had to pick something for improvement I would say that the receiver switch night light doesn’t turn on, not sure if this can be fixed via a firmware update or not but I did see it blink during the installation. Other than that, a MUST HAVE product for all smart homes.

This is a great upgrade to our old sliding dimmer switch. It works without a problem with the app and Alexa. “Alexa, turn on light” “Alexa, 50% (or whatever % you want) light” “Alexa, turn the light off” It saves the last (dimmer) setting when you turn it off. So if you have it 10% light output then you turned it off, the next time you turn it on it’ll be at 10% light output. -I like that- Installation is pretty straightforward -make sure you have the Meross app and you’re logged in. Make sure the main power switch is turned off!!- the switch wires are well labeled. The app has a step by step guide to get you through. Or if you’re a handy diy-er, you’ll get it installed in less than 5 minutes. If you are starting your smart home project, I highly recommend Meross’ product. They have a lot to get you started and they all work with just one app(!) and all of them (the ones I purchased -garage door opener, smart plugs, smart switch-) works with Alexa.

After latest update the switches are working perfectly. My original review is below. I was super excited by this product and it worked great...for about two weeks. Now the manual switch doesn’t work. I cannot turn the light on or off without my phone. I had a similar problem a couple of days ago and hit the circuit breaker to try and reset the product and that seemed to work for a few days and now I’m back to the manual switch failing again. It’s a bit frustrating. I’m hoping to find a way to update the product in hopes it will correct it he problem or else it will be returned. Original review: I don’t usually get very excited about light switches, but I am about this one. For a couple of years now I have been looking for a decent blue tooth enabled light switch that is dimmable as well as not overly expensive to run my bedroom lights. The switch is by the door and it’s a good distance from my bed, so I have often tripped over a dog toy or slipper while making my way to the bed. If I could only shut the lights off with my phone which is right beside me on my night table? I’ve tried a couple of pricey Bluetooth switches and returned them for not working well. The Meross smart WiFi dimmer switch is everything I wanted. Easy to install, nice looking led’s on the switch, and a very simple app to control the lights with, even when I’m away on vacation. Like many apps I am sure there will be some glitches, but so far I found it very straight forward and easy to use. The install was just as simple since the instructions pop up on your phone and walk you through it one step at a time. My other light switches run a black a white and a green (ground) wire. However after looking closely I noticed that the white wire coming from the switch was actually also connected to the black wire from the wall. Basically that is the break that the switch then opens or closed to allow the power to continue. Behind the switch was the white wire which you need to make this product work correctly. I attached white to white, the two blacks to the now two blacks after I separated them from the switch, and the green to the green. The switch came with wire twist connectors so it was really easy. I then turned the power back on and connected the WiFi and I was done. Less than 10 minutes for me. It’s been working great to date, and my package even came with two switches to make the price per unit even better. I couldn’t be happier.

Received the product a few weeks ago. I was able to connect it to my foyer chandelier and works exactly as I had hoped. Im now able to turn it on that light with my Alexa echo as well as dim it to the setting I would like. It was easy to install (just in case, I did some extra YouTube researching on how to install but the Meross App did explain how to connect it pretty well). Once connected, everything worked as intended. The Amazon listing was helpful and very informational about the product.

These 3-way dimmers with HomeKit support were the final piece to my HomeKit lighting puzzle! With these installed, now all of the lights in my house dim from 1% to 100%, all through the Meross app, and Apple’s native Home app. Installation couldn’t have been easier (you can do it through the Meross app and/or Home app - your choice!), and you won’t find a better price for HomeKit light switches. Oh, and there’s no hub required!

Keeps loosing connection